I. Ueno¹, T. Kishida²

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.1, pp. 55-60, 2008, DOI:10.3970/fdmp.2008.004.055

Abstract Phenomenon known as `tears of wine' arises on an inclined plate partially submerged in a bulk of alcohol-water mixture. This phenomenon apparently exhibits a periodic ordered structure, the flow field itself evolves quite complex feature; especially in the vicinity of the tear. In the present study, the authors paid their special attention to this unique, complex flow field of O(1 mm) with deformable surface. The flow pattern and the spatio-temporal particle behavior in the tear were reconstructed by applying three-dimensional particle tracking velocimetry (3-D PTV). More >

G.Pétré¹, K.Tshinyama, A. Azouni², S. Van Vaerenbergh¹

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.1, pp. 1-10, 2008, DOI:10.3970/fdmp.2008.004.001

Abstract This study illustrates a relevant and practical method to determine the effective surface tension gradient in a layer subjected to a lateral temperature difference. In general, this can be hardly performed in situ without perturbing the flow. For this reason we rely on an indirect determination approach. A simple model is developed that relates the surface tension gradient to other quantities that can be measured without introducing significant disturbances in the system. Measurements of these quantities are performed in a set-up where the flow corresponds with a good approximation to a one-dimensional model. A previously used set-up has been upgraded… More >

Huawei Han¹, Kamiel S. Gabriel²

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.4, pp. 287-298, 2006, DOI:10.3970/fdmp.2006.002.287

Abstract Data on air-water co-current two-phase annular flow in a tube with an inner diameter of 9.525 mm (3/8 in) were previously collected at both microgravity u-g and normal gravity (1-g) conditions. The data contained measurements of pressure drop, in addition to previously published data of liquid film thickness. This paper presents the results and analysis of the influence of flow pressure gradient on interfacial wave properties of annular flow at both microgravity and normal gravity. The examined wave properties include wave base thickness, wave height (or roughness height), wave spacing, wave speed and wave frequency. It was found that, the… More >

Sunil Punjabi¹, K. Muralidhar², P. K. Panigrahi²

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.2, pp. 95-106, 2006, DOI:10.3970/fdmp.2006.002.095

Abstract Convection in a differentially heated two-layer system consisting of air and water was studied experimentally, using laser-interferometry. The cavity used for flow visualization was square in cross-section and rectangular in-plan having dimensions of 447 × 32 × 32 mm³. Experiments performed over different layer thicknesses of water filled in a square cross-section cavity, the rest being air, are reported in the present work. The following temperature differences for each layer height were imposed across the hot and the cold walls of the superposed fluid layers: (i) ΔT=10K and (ii)ΔT =18 K. The present study was aimed at understanding the following… More >

Milica Radisic^1,2, Gordana Vunjak-Novakovic³

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.1, pp. 1-16, 2006, DOI:10.3970/fdmp.2006.002.001

Abstract To engineer cardiac tissue in vitro with properties approaching those of native tissue, it is necessary to reproduce many of the conditions found in vivo. In particular, cell density must be sufficiently high to enable contractility, which implies a three-dimensional culture with a sufficient oxygen and nutrient supply. In this review, hydrogels and scaffolds that support high cell densities are examined followed by a discussion on the utility of scaffold perfusion to satisfy high oxygen demand of cardiomyocytes and an overview of new bioreactors developed in our laboratory to accomplish this task more simply. More >

A. Filali¹, L. Khezzar^1,2

FDMP-Fluid Dynamics & Materials Processing, Vol.9, No.3, pp. 307-329, 2013, DOI:10.3970/fdmp.2013.009.307

Abstract Numerical investigations of purely-elastic instabilities occurring in creeping flows are reported in planar cross-slot geometries with both sharp and round corners. The fluid is described by the upper-convected Maxwell model, and the governing equations are solved using the finite element technique based on a steady (non-iterative) direct solver implemented in the POLYFLOWcommercial software (version 14.0). Specifically, extensive simulations were carried out on different meshes, with and without the use of flow perturbations, for a wide range of rheological parameters. Such simulations show the onset of flow asymmetries above a critical Deborah number (De). The effect of rounding the corners is… More >

V. Haslavsky, E. Miroshnichenko, E. Kit, A. Yu. Gelfgat

FDMP-Fluid Dynamics & Materials Processing, Vol.9, No.3, pp. 209-234, 2013, DOI:10.3970/fdmp.2013.009.209

Abstract Experimental and numerical observations of oscillatory instability of melt flow in a Czochralski model are compared, and a disagreement observed at small crystal dummy rotation rates is addressed. To exclude uncertainties connected with flow along the free surface, the latter is covered by a no-slip thermally insulating ring. Experiments reveal an appearance of oscillations at temperature differences smaller than the numerically predicted critical ones. At the same time, a steep increase of the oscillations amplitude is observed just beyond the computed threshold values. By increasing the dummy rotation gradually, we are able to qualitatively confirm the numerically predicted flow destabilization.… More >

Davood Kalantari¹

FDMP-Fluid Dynamics & Materials Processing, Vol.9, No.2, pp. 169-182, 2013, DOI:10.3970/fdmp.2013.009.169

Abstract In this study, a critical summary of existing spray/wall interaction models is given in synergy with a review of available experimental data. In particular, special attention is devoted to the limitations, difficulties and complexities of the most used approaches in the literatures. An attempt is also made to indicate the bottlenecks and criticalities which typically arise when investigators try to extend results obtained for isolated droplets to the more complex dynamics produced by spray impacts. More >

S.-A. B. Al Omari^1,2, E. Elnajjar¹

FDMP-Fluid Dynamics & Materials Processing, Vol.9, No.2, pp. 91-109, 2013, DOI:10.3970/fdmp.2013.009.091

Abstract In a previous numerical study (Al Omari, Int. Communication in Heat and Mass Transfer, 2011) the heat transfer enhancement between two immiscible liquids with clear disparity in thermal conductivity such as water and a liquid metal (attained by co- flowing them in a direct contact manner alongside each other in mini channel) was demonstrated. The present work includes preliminary experimental results that support those numerical findings. Two immiscible liquids (hot water and liquid gallium) are allowed experimentally to exchange heat (under noflow conditions) in a stationary metallic cup where they are put in direct contact. The experimental results confirm the… More >

S. Aggoune¹, E.H. Amara¹, M. Debiane²

FDMP-Fluid Dynamics & Materials Processing, Vol.9, No.1, pp. 61-75, 2013, DOI:10.3970/fdmp.2013.009.061

Abstract The effects of inert assisting gas nature and velocity on laser cut quality are investigated. A pure fusion cutting process just above melting point is considered, where the molten steel velocity is given as a function of the two acting forces represented by the pressure gradient and the frictional forces applied by the laminar gas flow. In the case of nitrogen assisting gas, the stainless steel melt film exhibits a visible separation point. The point where the melt flow is separated out from the solid wall depends strongly on the gas velocity. It is pushed down the cut surface when… More >