Romana Basit¹, Xinyang Li¹, Zheqing Huang¹, Qiang Zhou^1,2,*

CMES-Computer Modeling in Engineering & Sciences, Vol.136, No.2, pp. 1509-1526, 2023, DOI:10.32604/cmes.2023.025308

Abstract Direct Numerical Simulations have been carried out to study the forced convection heat transfer of flow through fixed prolate particles for a variety of aspect ratios ar = {5/4, 5/3, 5/1} with Reynolds number (Re) up to 100. Three variations of the solid volume fraction c = {0.1, 0.2, 0.3} with four Hermans orientation factors S = {−0.5, 0, 0.5, 1} are studied. It has been found that changes in S cause prominent variations in the Nusselt number. In general, Nusselt number increases with the decrease of S. For all three aspect ratios, the Nusselt number remains a linear function… More > Graphic Abstract

Daoming Shen^1,*, Jinhong Xia¹, Chao Gui¹, Songtao Xue²

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.6, pp. 1411-1424, 2023, DOI:10.32604/fdmp.2023.024924

Abstract The thermal transmission coefficient for a micro-ribbed tube has been determined using theoretical relationships and the outcomes of such calculations have been compared with experiments conducted using a R1234yf refrigerant undergoing condensation. In particular four theoretical single-phase flow and three multi-phase flow models have been used in this regard. The experimental results show that: the Oliver et al. criterion equation overestimates the experimental results as its accuracy is significantly affected by the specific conditions realized inside micro-fin tubes; the Miyara et al. criterion equation prediction error is less than 15%; the Cavallini et al. approach gives the highest prediction accuracy;… More >

Toufik Sahabi^1,*, Smain Balaska²

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.4, pp. 977-990, 2023, DOI:10.32604/fdmp.2022.022059

Abstract The heat transfer equation is used to determine the heat flow by conduction through a composite material along the real axis. An analytical dimensionless analysis is implemented in the framework of a separation of variables method (SVM). This approach leads to an Eigenvalues problem that is solved by the Newton’s method. Two types of dynamics are found: An unsteady condition (in the form of jumps or drops in temperatures depending on the considered case), and a permanent equilibrium (tending to the ambient temperature). The validity and effectiveness of the proposed approach for any number of adjacent layers is also discussed.… More > Graphic Abstract

Shrikant Arunrao Thote^*, Netra Pal Singh

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.3, pp. 711-722, 2023, DOI:10.32604/fdmp.2022.021651

Abstract The thermo-hydraulic properties of circular tubes with a twisted tape inside (used accordingly to induce turbulence and enhance heat transfer through the tube wall) are described for Reynolds Numbers ranging from 830 to 1990. Tapes twisted with the three distinct twist ratios are considered, namely, 6, 4.4 and 3. Air is used as the working fluid in several tests. For the sake of comparison, the standard tube with no insert is also examined. It is shown that in the presence of the twisted tape, the ‘frictional factor’, ‘Nusselt Number’ and the ‘thermal performance factor’ are much higher than those obtained… More >

Mohammad Saraireh^*

Intelligent Automation & Soft Computing, Vol.36, No.1, pp. 57-70, 2023, DOI:10.32604/iasc.2023.032050

Abstract With the growing global energy and environmental problems, electric vehicles that are both environmentally friendly and cost effective have seen rapid growth. An electrified vehicle’s effective thermal management must include all of the vehicle’s systems. However, optimizing the thermal behavior of each component is insufficient. A lithium-ion battery’s operating temperature has a significant impact on its performance. When working at low temperatures, the internal resistance of lithium-ion batteries increases, the available energy and power of the system decreases, and lithium precipitation caused by low-temperature charging may cause safety issues; high-temperature operation and temperature inconsistency between battery cells will cause accelerated… More >

Mehdi Moslemi¹, Motahare Mahmoodnezhad¹, S. A. Edalatpanah^1,*, Sulima Ahmed Mohammed Zubair², Hamiden Abd El-Wahed Khalifa^2,3

CMES-Computer Modeling in Engineering & Sciences, Vol.134, No.3, pp. 1957-1973, 2023, DOI:10.32604/cmes.2022.021481

Abstract In this research, a numerical study of mixed convection of non-Newtonian fluid and magnetic field effect along a vertical wavy surface was investigated. A simple coordinate transformation to transform wavy surface to a flat surface is employed. A cubic spline collocation numerical method is employed to analyze transformed equations. The effect of various parameters such as Reynolds number, volume fraction 0-, Hartmann number, and amplitude of wave length was evaluated in improving the performance of a wavy microchannel. According to the presented results, the sinusoidal shape of the microchannel has a direct impact on heat transfer. By increasing the microchannel… More >

Umair Khan^1,2, Aurang Zaib³, Anuar Ishak¹, Iskandar Waini⁴, El-Sayed M. Sherif⁵, Dumitru Baleanu^6,7,8,*

CMES-Computer Modeling in Engineering & Sciences, Vol.134, No.2, pp. 1371-1392, 2023, DOI:10.32604/cmes.2022.020911

Abstract The utilization of solar energy is essential to all living things since the beginning of time. In addition to being a constant source of energy, solar energy (SE) can also be used to generate heat and electricity. Recent technology enables to convert the solar energy into electricity by using thermal solar heat. Solar energy is perhaps the most easily accessible and plentiful source of sustainable energy. Copper-based nanofluid has been considered as a method to improve solar collector performance by absorbing incoming solar energy directly. The goal of this research is to explore theoretically the Agrawal axisymmetric flow induced by… More >

Farah Zemani-Kaci^*, Amina Sabeur-Bendhina

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 513-539, 2023, DOI:10.32604/fdmp.2022.021974

Abstract A two-dimensional numerical study of laminar natural convection in a square enclosure filled with air with a wall partially heated on the bottom is presented. The heat source is located on the lower wall with different heated widths varied from 20 to 80%(ε = 0.2–0.8) of the total width of the lower wall and different heights h = H/4 and H/2 of the partition. The effect of the partition height on the main system dynamics is investigated through solution of the two-dimensional Navier–Stokes equations and the energy equation by means of a finite volume method based on the SIMPLE algorithm.… More > Graphic Abstract

Muhammad A. Sadiq^1,2,*, Nadeem Abbas³, Haitham M. S. Bahaidarah⁴, Mohammad Amjad⁵

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 471-486, 2023, DOI:10.32604/fdmp.2022.021133

Abstract We present the results of an investigation into the behavior of the unsteady flow of a Casson Micropolar nanofluid over a shrinking/stretching curved surface, together with a heat transfer analysis of the same problem. The body force acting perpendicular to the surface wall is in charge of regulating the fluid flow rate. Curvilinear coordinates are used to account for the considered curved geometry and a set of balance equations for mass, momentum, energy and concentration is obtained accordingly. These are turned into ordinary differential equations using a similarity transformation. We show that these equations have dual solutions for a number… More >

Alim Al Ayub Ahmed^1,*, Salim Oudah Mezan², Binyamin³, Murtadha Doghiam Abdullah⁴, Elena Tesleva⁵, Linar G. Akhmetov⁶, Rustem Zalilov⁷, Mustafa M. Kadhim^8,9,10, Abduladheem Turki Jalil^11,12

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.1, pp. 15-24, 2023, DOI:10.32604/fdmp.2022.019922

Abstract The utilization of vortex generators to increase heat transfer from cylinders installed inside a duct is investigated. In particular, a channel containing eight cylinders with volumetric heat sources is considered for different values of the Reynolds number. The effective possibility to use vortex generators with different sizes to increase heat transfer and, consequently, reduce the surface temperature of the cylinders is examined. Also, the amount of pressure drop inside the channel due to the presence of vortex generators is considered and compared with the cases without vortex generators. The results show that although the addition of generators increases the pressure… More >