Yan Shen¹, Hong Zhang^1,2,3, Hui Xu¹, Tong Bai¹, Ping Yu¹

FDMP-Fluid Dynamics & Materials Processing, Vol.10, No.1, pp. 63-81, 2014, DOI:10.3970/fdmp.2014.010.063

Abstract Single-unit and multi-unit models of porous media (metal felts) have been used to investigate thermal fluid-structure interaction phenomena in a liquid sodium system. Micro-scale aspects have been studied via numerical simulations. The permeability of metal felts has been measured experimentally to verify the reliability of the models used. This integrated approach has allowed a proper evaluation of the interdependencies among phenomena on different scales (including relevant information on skeleton deformation and pressure drop as a function of different parameters). Pressure drop generally increases with velocity and heat flux for both laminar and turbulent flows. The final deformation is greater when… More >

M.R. Arab^1,2, E. Semma³, B. Pateyron¹, M. El Ganaoui¹

FDMP-Fluid Dynamics & Materials Processing, Vol.5, No.2, pp. 161-176, 2009, DOI:10.3970/fdmp.2009.005.161

Abstract In this work, flows in porous media are simulated by using a Lattice Boltzmann Method (LBM). A model D2Q9 with a single collision operator is proposed. This method is applied on 2D digital images obtained by a Scanning Electron Microscope technique (SEM), and followed by a special treatment in order to obtain an image of synthesis that is finally read by the numerical code. The first results tested on two-dimensional configurations show the reliability of this strategy in simulating with a good accuracy phenomena of heat and mass transport. The numerical study is extended to the prediction of physical parameters… More >

T. J Jaber¹, M. Khawaja¹, M.Z. Saghir¹

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.4, pp. 271-286, 2006, DOI:10.3970/fdmp.2006.002.271

Abstract This paper numerically investigates the interaction between thermodiffuion and buoyancy driven convection in a laterally heated vertical porous cavity for different permeability. The Firoozabadi model is applied to binary hydrocarbon mixtures: (i) the mixture of 1,2,3,4 tetrahydronaphtalene (THN) and dodecane (C12) with mass fraction of 50% for each component, (ii) 1,2,3,4 tetrahydronaphtalene and isobutylbenzene (IBB) with mass fraction of 50% for each component, and (iii) isobutylbenzene and dodecane with mass fraction of 50% for each component. The thermal and molecular diffusion coefficients, which are functions of the temperature and other properties of mixture, are calculated at each point of the… More >

N. Labed¹, L. Bennamoun², J.P. Fohr³

FDMP-Fluid Dynamics & Materials Processing, Vol.8, No.4, pp. 423-436, 2012, DOI:10.3970/fdmp.2012.008.423

Abstract Intrinsic and relative permeability are indispensable parameters for performing transfers in porous media. In this paper, the conception and ensuing exploitation of a new testing ground for measuring the relative permeability of water and nitrogen are presented. The experimental work was elaborated in the Laboratory of Thermal Studies in Poitiers, (France) where brick samples were used to verify the performance of the proposed testing strategy. The results prove the existence of several stages during the drainage and the imbibitions. In particular, the three stages observed for the case of gas permeability reduce to only two steps for liquid permeability. Comparison… More >

Viveca Wallqvist¹, Per M. Claesson², Agne Swerin¹, Patrick A. C. Gane^3,4,3, Joachim Schoelkopf³

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.2, pp. 85-98, 2008, DOI:10.3970/fdmp.2008.004.085

Abstract It has been shown that talc powder can be compacted into tablets with a preferred orientation of the platelets. The tablets can be obtained with different controlled porosity depending on pressing methods and applied pressure. The tablets can be obtained with or without additives, which may, in turn, be adsorbed. The orientation of the high aspect ratio platy talc, the surface chemistry imparted by the additives and the transported fluid influence the imbibition and permeation rates. Non-polar hexadecane displays a higher imbibition and permeability than water for all particulate orientations during short timescale absorption, likely due to the oleophilic nature… More >

Yi Xue^1,2,3, Faning Dang², Rongjian Li², Liuming Fan², Qin Hao⁴, Lin Mu², Yuanyuan Xia²

CMC-Computers, Materials & Continua, Vol.54, No.1, pp. 43-59, 2018, DOI:10.3970/cmc.2018.054.043

Abstract In the seepage-stress-damage coupled process, the mechanical properties and seepage characteristics of coal are distinctly different between pre-peak stage and post-peak stage. This difference is mainly caused by damage of coal. Therefore, in the process of seepage and stress analysis of coal under the influence of excavation or mining, we need to consider the weakening of mechanical properties and the development of fractures of damaged coal. Based on this understanding, this paper analyzes the influence of damage on mechanics and seepage behavior of coal. A coupled model is established to analyze the seepage-stress-damage coupled process of coal. This model implemented… More >

Shifeng Xue^1,2, Xiuxing Zhu^1,2, Lin Zhang³, Shenghu Zhu⁴, Guigen Ye^1,5

CMC-Computers, Materials & Continua, Vol.51, No.1, pp. 21-42, 2016, DOI:10.3970/cmc.2016.051.021

Abstract A perforating hole is a channel through which the oil and gas in a reservoir pass into the production well bore. During the process of perforating due to explosion, the surrounding sandstone will be damaged to a certain extent, which will increase the well bore skin and lead to the decrease of production consequently. In this work a mechanical model of perforating damage is developed to describe the influences of perforating due to explosion on the porosity and permeability of the surrounding sandstone near the compaction zone. Based on this developed model, the important data related to the damage of… More >

Yi Xue^1,2, Feng Gao^1,2,3, Xingguang Liu⁴, Xiru Li²

CMC-Computers, Materials & Continua, Vol.47, No.2, pp. 127-141, 2015, DOI:10.3970/cmc.2015.047.127

Abstract In order to study the effect of high pressure water jet cutting technology on the permeability of single coal seam, we use the damage variable to describe the fracture distribution of coal seam, develop the 3-D finite element program based on the damage theory, and then analyze the damage distribution of coal seam after drilling and slotting. Using MTS815 rock mechanics testing system and the permeability test system, we conduct the permeability test and get the relationship between permeability and damage. Based on the damage distribution of coal seam after drilling and slotting and the permeability change law, we analyze… More >

Bui Duc Thuan^1,2, Wong Yonghui², Chua Kian Jon², Ng Kim Choon²

CMC-Computers, Materials & Continua, Vol.47, No.2, pp. 89-105, 2015, DOI:10.3970/cmc.2015.047.089

Abstract The cup method and dynamic moisture permeation cell (DMPC) method are two common techniques used to determine the water vapor permeation properties of a membrane. Often, ignoring the resistance of boundary air layers to the transport of water vapor results in the water vapor permeance of the membrane being underestimated in practical tests. The measurement errors are higher with highly permeable membranes. In this study, the two methods were simulated using COMSOL Multiphysics platform and the extent of the error was evaluated. Initial results showed that the error is equally high in both methods. With the correction for the still… More >