Hui Jiang^a,b, Daming Wu^a,b,c, Jian Zhuang^a,b,*, Ying Liu^a,b,c, Changqing Huang^a,b

Frontiers in Heat and Mass Transfer, Vol.6, pp. 1-6, 2015, DOI:10.5098/hmt.6.14

Abstract A new type of metal-plastic composite heat radiator with hemispherical microstructure array was proposed in this paper. The influence of the geometrical parameters of the microstructure array, including size of the hemisphere, configuration of hemisphere, tilt angle of the radiator, thermal conductivity and radiation emissivity of the plastic, on the process of heat transfer under natural convection were numerically simulated. It was concluded that the metal-plastic composite heat radiator with hemispherical microstructure array had comparable heat transfer behaviors with those of metal heat radiator. So it is possible to replace metal heat radiator by such a metal-plastic composite heat radiator… More >

Swetha Lanka¹, Venkata Subrahmanyam Sajja^1,*, Dhaneshwar Prasad²

Frontiers in Heat and Mass Transfer, Vol.21, pp. 385-405, 2023, DOI:10.32604/fhmt.2023.042544

Abstract An attempt is made to analyse some lubrication characteristics of rigid cylindrical asymmetric rollers under adiabatic and isothermal boundaries with rolling and sliding motion lubricated by a non-Newtonian incompressible Bingham plastic fluid under the behaviour of line contact. Here the lower surface is considered to move quicker than that of the upper surface; and the Roelands viscosity model is considered and assumed to depend upon the fluid pressure and the mean film temperature. The governing equations for fluid flow such as equations of motion with continuity and the momentum energy equation are solved using Runge-Kutta forth order and MATLAB is… More >

Peidong Wu^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.26, No.1, pp. 1-1, 2023, DOI:10.32604/icces.2023.010491

Abstract The material anisotropy of an aluminum sheet alloy is determined by performing tensile tests at different angles with respect to the rolling direction (RD). To study the effect of pre-straining on the evolution of material anisotropy, a very wide sheet is stretched to different strains in the transverse direction (TD). The material in the central region is very close to a state of in-plane plane strain tension. Small tensile samples are cut from the central region of the pre-strained wide sample. Tensile tests are then performed on these small tensile samples. By comparing the differences in the flow stress vs.… More >

Haiming Zhang^1,2,*, Shilin Zhao^1,2, Zhenshan Cui^1,2

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.4, pp. 1-1, 2023, DOI:10.32604/icces.2023.08884

Abstract Particle-reinforced aluminum matrix composites (PRAMCs) have great potential for application in aerospace, automobile, defense, and electronics due to their high specific strength and stiffness and good resistance to wear and corrosion. Achieving a superior trade-off between the strength and ductility of PRAMCs necessitates an elaborative control of the microstructures, like the size and distribution of particles, as well as grain size, morphology, and texture of the matrix. The multiscale interaction between the particles and the matrix’s microstructure is insufficiently understood due to the lagging of high-resolved in-situ characterization. This work proposes a nonlocal physically based crystal plasticity (CP) modeling approach… More >

Lifeng Gan¹, Baoyin Zhu², Chao Ling^1,*, Esteban P. Busso¹, Dongfeng Li¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.3, pp. 1-1, 2023, DOI:10.32604/icces.2023.010397

Abstract Heat-resistant austenitic stainless steels are widely used in the final stages of superheater and reheater in in the new generation of fossil fuel power stations, due to their high creep strength. Similar weld joints, fabricated using gas tungsten arc welding, for connecting different components made of the heat resistant austenitic stainless steels usually suffer from premature failures at elevated temperature [1]. Experimental studies showed that cracks may nucleate in the heat affected zone or weld metal of the similar welded joints under service conditions. In order to reveal the physical origin of unexpected failures of the weld joints, a microstructure-based… More >

Shi Dai¹, Yanping Lian^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.3, pp. 1-1, 2023, DOI:10.32604/icces.2023.010175

Abstract In recent years, metal additive manufacturing (AM) has gained increasing attention from various industries. However, there are few studies on the thermal deformation behavior of additively manufactured metallic components, which is vital to pushing its applications’ boundary. In this work, we first experimentally investigate the mechanical behavior of AlSi10Mg produced by laser powder bed fusion under different temperatures and strain rates. A crystal plasticity finite element model is adopted to provide insights into the intrinsic deformation mechanisms. The model is validated by comparing it with the flow behaviors and dislocation evolutions observed in experiments at different conditions. The strain distributions… More >

Yinan Cui^1,*, Zhijie Li¹, Zhangtao Li¹, Zhanli Liu¹, Zhuo Zhuang¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.3, pp. 1-1, 2023, DOI:10.32604/icces.2023.010121

Abstract How the plasticity features influence the fracture behaviours of material is a critical question but remains far from well understood. To disclose this mystery, a multiscale plasticity-fracture coupled model is developed, which considers the atomistic-scale dislocation motion mechanism, the mesoscopic scales of discrete crack-dislocation interactions, and the continuum scale of crystalline plastic-fracture response. Body center cubic (bcc) material is chosen as an example to demonstrate the effectiveness of the developed model due to their wide applications and their special plasticity features, such as strong temperature dependence and non-Schmid effect. Several new insights about the fracture behaviour of bcc material are… More >

Qilin Xiong^1,2,*, Wen An^1,2, Chuanzhi Liu^1,2

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.3, pp. 1-1, 2023, DOI:10.32604/icces.2023.010044

Abstract Shear localization is an important failure mode, or even the dominant mode in metals at high-strain rates. However, it is a great challenge to accurately predict the occurrence and evolution of shear localization in metals at the high-strain rate deformation. Here, a dislocation-based crystal plasticity constitutive model with a crucial mechanism of shear instability, namely dynamic recrystallization, was developed. The evolution equations of dislocation density and grain size in the process of dynamic recrystallization were proposed and incorporated into the new constitutive model. The threshold of the stored energy in crystals was used as the criterion for the occurrence of… More >

Qishan Huang¹, Haofei Zhou^2,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.3, pp. 1-1, 2023, DOI:10.32604/icces.2023.010014

Abstract Nanostructured metals contain vast amount of grain boundaries which are crucial to their mechanical behaviors. The plastic deformation mechanisms mediated by grain boundaries have been attracted increasing attentions in recent years. Our recent studies have been focused on using atomistic simulations to understand the grain boundary mediated plastic deformation mechanisms including deformation twinning initiated by dislocation nucleation from grain boundaries [1], cyclic plastic deformability governed by reversible slip of grain boundary dislocations [2], and extreme shear deformation of nanocrystals induced by twin boundary sliding [3]. We have also proposed a misorientation-dependent model to explain the transition between grain boundary migration… More >

Yao Lu¹, Jianyu Chen², Dianlei Feng^3,*, Moubin Liu^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.3, pp. 1-2, 2023, DOI:10.32604/icces.2023.010004

Abstract CFRPs (carbon fiber reinforced plastics), as a kind of fiber-reinforced plastic, present various advantages over traditional materials regarding the specific strength, stiffness, and corrosion resistance. For this reason, CFRPs are widely used in the space industry, like satellites and space stations, which are easily subjected to the HVIs (hypervelocity impacts) threatened by space debris. In order to mitigate the damage of HVIs and protect the spatial structures, it is necessary to predict the HVI process on CFRPs. Smoothed particle hydrodynamics (SPH) method, as a mesh-free particle-based method, has been widely applied for modeling HVI problems due to its special advantages… More >