D. Bothe^1,2, M. Kröger¹, H.-J. Warnecke³

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.3, pp. 303-316, 2011, DOI:10.3970/fdmp.2011.007.303

Abstract In this paper numerical results on reactive mass transfer from single gas bubbles to a surrounding liquid are presented. The underlying numerical method is based on the solution of the incompressible two-phase Navier-Stokes equations. The Volume-of-Fluid method is applied for the description of the liquid-gas interface. Within the numerical approach the concentration of the transfer component is represented by two separate variables, one for each phase. Numerical results are in good agreement with experimental data. More >

Carole Planchette¹, Elise Lorenceau¹, Günter Brenn²

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.3, pp. 279-302, 2011, DOI:10.3970/fdmp.2011.007.279

Abstract This work is dedicated to a general description of collisions between two drops of immiscible liquids. Our approach is mainly experimental and allows us to describe the outcomes of such collisions according to a set of relevant parameters. Varying the relative velocity U as well as the impact parameter X we can build for each pair of investigated liquids a nomogram X,U showing three possible regimes: coalescence, head-on separation and off-center separation. In this paper, we also study the influence of the liquid properties, i.e. viscosity, density, surface and interfacial tensions using a set of aqueous glycerol solutions together with… More >

Robert Rundqvist¹, Andreas Mark¹, Fredrik Edelvik¹, Johan S. Carlsson¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.3, pp. 259-278, 2011, DOI:10.3970/fdmp.2011.007.259

Abstract Multiphase flow simulation using Smoothed Particle Hydrodynamics (SPH) has gained interest during recent years, mostly due to the inherent flexibility of the method and the physically rather intuitive formulation of extra constitutive equations needed when dealing with for instance non-Newtonian flows. In the work presented here, simulations based on an SPH model implemented in the flow solver IBOFlow has been used for simulation of robotic application of sealing material on a car body. Application of sealing materials is done in order to prevent water leakage into cavities of the body, and to reduce noise. In off-line programming of the robots… More >

A. Mark^1,2, R. Rundqvist¹, F. Edelvik¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.3, pp. 241-258, 2011, DOI:10.3970/fdmp.2011.007.241

Abstract In the literature immersed boundary methods are employed to simulate complex flows around moving arbitrary bodies without the necessity of remeshing. These methods employ a regular Eulerian mesh to simulate the fluid flow and a Lagrangian representation of the boundary of the bodies. The two representations can be coupled through an immersed boundary condition constraining the fluid to exactly follow the boundary of the bodies (immersed boundaries). Typically such methods suffer from accuracy problems, that arise from spurious mass fluxes over the immersed boundary (IB), pressure boundary conditions or high density ratios. The mirroring IB method Mark (2008); Mark and… More >

S. Homma¹, M. Yokotsuka¹, T. Tanaka¹, K. Moriguchi¹, J. Koga¹, G. Tryggvason²

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.3, pp. 231-240, 2011, DOI:10.3970/fdmp.2011.007.231

Abstract We develop a three-fluid front-tracking method in order to simulate the motion of an axisymmetry compound droplet, which consists of three immiscible fluids separated by two different interfaces. The two interfaces of the compound droplet are represented by two different sets of the front-tracking elements immersed on the Eulerian grid mesh, where the velocities and the pressure are calculated. The density and viscosity profiles with jumps at the interfaces are successfully determined from the location and the connection information of the front-tracking elements. The motion of a compound droplet is simulated on axisymmetric cylindrical coordinates. The results show that the… More >

R. Abdeljabar¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 217-230, 2011, DOI:10.3970/fdmp.2011.007.217

Abstract In this paper, we discuss a new technique for desalination based on the principles of the Soret effect. In particular, the method stems from the peculiar behavior of the solute in a solution of sodium chloride (i.e. salty water layer) of uniform concentration being less or equal to 5wt% under the effect of an imposed temperature gradient with average temperature equal to 12oC. The Soret coefficient may be positive or negative according to whether the temperature of the solution is above or below 12oC. As two diffusion processes (one parallel to the temperature gradient and the other anti-parallel) can occur… More >

S. Srinivasan¹, M. Z. Saghir¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 201-216, 2011, DOI:10.3970/fdmp.2011.007.201

Abstract CFD simulations have been made to understand the impact of the vibrations of the ISS on the thermodiffusion process. Simulations were made for two ternary hydrocarbon mixtures and one binary associated mixture. While one of the ternary mixture was at a pressure of 35 MPa, the second ternary mixture as well as the binary mixture were at a pressure of 0.101325 MPa. The analysis of the results showed that imposing the ISS vibrations had a profound effect on the Soret effect in all three systems. More precisely, in all three mixtures, a single convective flow cell is established. Such a… More >

Massimo Corcione¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 175-200, 2011, DOI:10.3970/fdmp.2011.007.175

Abstract Free convection heat transfer in nanofluids from horizontal isothermal cylinders is investigated theoretically. The main idea upon which the present work is based is that nanofluids behave more like a single-phase fluid rather than like a conventional solid-liquid mixture. This assumption implies that all the convective heat transfer correlations available in the literature for single-phase flows can be extended to nanoparticle suspensions, provided that the thermophysical properties appearing in them are the nanofluid effective properties calculated at the reference temperature. In this connection, two empirical equations, based on a wide variety of experimental data reported in the literature, are proposed… More >

R. C. Bataller¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 153-174, 2011, DOI:10.3970/fdmp.2011.007.153

Abstract We present a numerical study of the flow and heat transfer of an incompressible upper-convected Maxwell (UCM) fluid in the presence of an uniform transverse magnetic field over a porous stretching sheet taking into account suction at the surface as well as viscous dissipation and thermal radiation effects. Selected similarity analyses have been carried out by means of a numerical implementation. The effects on the velocity and temperature fields over the sheet of the parameters like elasticity number, suction velocity, magnetic parameter, radiation parameter, Prandtl number and Eckert number are also analyzed. More >

M. N. Noui-Mehidi¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 141-152, 2011, DOI:10.3970/fdmp.2011.007.141

Abstract The present work is concerned with a numerical study of the performance of a conical annular centrifugal contractor through the analysis of the flow properties when the apex angle is changed for different imposed axial flows. The calculations revealed the advantage of using conical annular centrifugal contractors compared to the cylindrical annular centrifuges. The study is conducted by a comparison analysis of the hydrodynamics of fluid flow in both conical and cylindrical contractors where moderate axial flows are imposed. In both systems the outer body is stationary while the inner rotor is maintained at constant speed. The calculations are achieved… More >