Davood Kalantari¹, Cameron Tropea²

FDMP-Fluid Dynamics & Materials Processing, Vol.10, No.1, pp. 37-61, 2014, DOI:10.3970/fdmp.2014.010.037

Abstract This study presents a combined experimental and theoretical investigation on the formation and spreading of a liquid film on a flat and rigid wall due to spray impact. A dual-mode phase Doppler instrument is used to characterise the spray while the average film thickness is measured using a high-speed CCD camera. The experimental results are complemented with theoretical expressions derived under the assumption that the spray is stationary. A new model for the prediction of the average wall film thickness is formulated taking into account the mean Reynolds number of the impacting drops, the flux density of the impacting droplets,… More >

H. C. Kuhlmann¹, M. Lappa², D. Melnikov³, R. Mukin¹,F. H. Muldoon¹, D. Pushkin⁴, V. Shevtsova², I. Ueno⁵

FDMP-Fluid Dynamics & Materials Processing, Vol.10, No.1, pp. 1-10, 2014, DOI:10.3970/fdmp.2014.010.001

Abstract The rapid accumulation of particles suspended in a thermocapillary liquid bridge is planned to be investigated during the JEREMI experiment on the International Space Station scheduled for 2016. An overview is given of the current status of experimental and numerical investigations of this phenomenon. More >

V. Carandente¹, R. Savino¹, M. Iacovazzo¹, C. Boffa

FDMP-Fluid Dynamics & Materials Processing, Vol.9, No.4, pp. 461-484, 2013, DOI:10.3970/fdmp.2013.009.461

Abstract The article deals with the aerothermal analysis of a sample-return hypersonic capsule reentering on Earth from an interplanetary exploration mission. The main objective of the work is to estimate the heat flux distribution on the capsule surface and to perform one-dimensional thermal analyses for its ablative heat shield. After a short review of sample-return missions, the numerical models implemented are described and the computational results, obtained along a feasible reentry trajectory, are presented and discussed. Particular attention has been paid to compare the convective stagnation point heat fluxes obtained by means of Computational Fluid Dynamic (CFD) analyses with the ones… More >

H. Chanson¹, K.K. Tan²

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.4, pp. 403-418, 2011, DOI:10.3970/fdmp.2011.007.403

Abstract A tidal bore is a wall of water propagating upstream as the tidal flow turns to rising into an estuary with a tidal range larger than 5 to 6 m and the bathymetry that amplifies the tidal wave. The bore front is a shock characterised by a singularity of the free-surface and pressure and velocity fields. This study aims to characterise the impact of tidal bores on the turbulent dispersion of fish eggs. Some physical modelling was performed based upon a Froude similitude and the tracking of plastic beads acting as fish egg proxies was conducted under controlled flow conditions… More >

M. Do-Quang¹, A. Carlson¹, G. Amberg¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.4, pp. 389-402, 2011, DOI:10.3970/fdmp.2011.007.389

Abstract Inkjet technology has been recognized as one of the most successful and promising micro-system technologies. The wide application areas of printer heads and the increasing demand of high quality prints are making ink consumption and print see-through important topics in the inkjet technology. In the present study we investigate numerically the impact of ink droplets onto a porous material that mimics the paper structure. The mathematical framework is based on a free energy formulation, coupling the Cahn-Hilliard and Navier Stokes equations, for the modelling of the two-phase flow. The case studied here consists of a multiphase flow of air-liquid along… More >

T. Uchiyama¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.4, pp. 371-388, 2011, DOI:10.3970/fdmp.2011.007.371

Abstract This study proposes a three-dimensional grid-free method to simulate particle-laden gas flows. It is based on a vortex method. The flow region is not resolved into computational grids, but the gas vorticity field is discretized by vortex elements. The behavior of the vortex element and the particle motion are simultaneously calculated by using the Lagrangian approach. Eight cubic cells are locally allocated around each particle to compute the effect of the particle motion on the gas flow. In each cell, the change in the vorticity due to the particle is calculated, and it is considered by generating a vortex element… More >

Y.Q. He, Q.C. Bi¹, D.X. Shi¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.4, pp. 357-370, 2011, DOI:10.3970/fdmp.2011.007.357

Abstract The behavior of a single air bubble rising in magnetic fluids without magnetic fields is visualized using a mini-gap between two parallel vertical glass plates. Water-based Fe3O4 magnetic fluids with particle volume concentration of 6.33 % and density 1261.96 kgm - 3 are filled in these gaps and a single air bubble is produced through the orifice at the bottom of the gap. The thicknesses of the gaps are 1 and 2 mm, respectively. Diameters of the orifices are 0.64 and 1.02 mm for 1 mm gap, and 0.64, 1.02 and 1.6 mm for 2 mm gap. In addition, four… More >

J.J. Derksen¹, D. Eskin²

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.4, pp. 341-356, 2011, DOI:10.3970/fdmp.2011.007.341

Abstract Direct simulations of laminar solid-liquid flow in micro-channels with full resolution of the solid-liquid interfaces have been performed. The solids phase consists of simple agglomerates, assembled of monosized, spherical particles. The flow of the interstitial liquid is solved with the lattice-Boltzmann method. Solids and fluid dynamics are two-way coupled. The simulations keep track of the flow-induced forces in the agglomerates. The effects of agglomerate type (doublets, triplets, and quadruplets), solids loading, and channel geometry on (the statistics of the) flow and collision-induced forces have been investigated. By comparing these forces with agglomerate strength, we would be able to assess the… More >

T. Sanada¹, K. Ando², T. Colonius²

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.4, pp. 329-340, 2011, DOI:10.3970/fdmp.2011.007.329

Abstract When a droplet impacts a solid surface at high speed, the contact periphery expands very quickly and liquid compressibility plays an important role in the initial dynamics and the formation of lateral jets. The high speed impact results in high pressures that can account for the surface erosion. In this study, we numerically investigated a high speed droplet impacts on a solid wall. The multicomponent Euler equations with the stiffened equation of state are computed using a FV-WENO scheme with an HLLC Riemann solver that accurately captures shocks and interfaces. In order to compare the available theories and experiments, 1D,… More >

Malcolm R. Davidson¹, Dalton J.E. Harvie¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.3, pp. 317-328, 2011, DOI:10.3970/fdmp.2011.007.317

Abstract A volume-of-fluid numerical method, adapted by the authors [Harvie, Cooper-White and Davidson (2008)] to simulate the flow of viscoelastic fluids, is used to predict deformation of a viscoelastic droplet carried by an immiscible Newtonian liquid through an axisymmetric microfluidic contraction-expansion. Values of the capillary number and elasticity number are chosen based on corresponding values for a rectangular contraction for which a reentrant cavity at the rear of the drop and subsequent encapsulation behaviour was observed experimentally by Harvie, Cooper-White and Davidson (2008). A reentrant cavity, similar to the observed one, is predicted; however, encapsulation is not achieved. Unexpectedly, a narrow… More >