Lei Guo^1,2,3, Zekun Wang¹, Lixia Guo^1,2,3,*, Pingping Chen¹

Journal of Renewable Materials, Vol.11, No.1, pp. 453-471, 2023, DOI:10.32604/jrm.2023.023315

Abstract Taking an industrial sludge and its preparation of sludge wrap shell aggregates (WSAs) instead of sand to prepare baking-free brick as the research object, the development law of mechanical properties and the influence mechanism of macro and micro characteristic parameters of the bricks under different sludge and WSAs replacement rates were studied through the macroscopic mechanical properties test, with the help of nuclear magnetic resonance (NMR), transmission electron microscopy-energy spectrum and other testing technology and pores and cracks analysis system (PCAS) software. The results showed that the compressive strength of each sample decreased with the increase of sludge content. When… More > Graphic Abstract

Xueyuan Wei, Yang Bai^*, Qi Chen^*

Journal of Renewable Materials, Vol.11, No.1, pp. 61-77, 2023, DOI:10.32604/jrm.2023.022773

Abstract Due to the long carrier lifetime, high carrier mobility, and high absorption coefficient of perovskite materials, the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has increased from 3.8% in 2009 to 25.7% in 2021, which have already surpassed the PCE of thin-film solar cells and closes to the efficiency of Si-based photovoltaics (26.7%). Therefore, PSCs have become a promising clean energy technology for commercialization. However, the low defect formation energy of perovskite leads to a higher defect density than other conventional photovoltaic materials. It results in severe non-radiative recombination, limiting its further development and the commercialization. In this… More > Graphic Abstract

Jiayu Chang¹, Qingying Ding¹, Chong Zhong¹, Yao Long², Zhuanquan Xiao³, Hai Luo¹, Yuling Yang¹, Zongde Wang¹, Shengliang Liao¹, Jinzhu Chen², Shangxing Chen^1,*, Ji Zhang^1,*

Journal of Renewable Materials, Vol.11, No.1, pp. 379-391, 2023, DOI:10.32604/jrm.2023.022535

Abstract (E) ω-formylcamphene was synthesized from α-pinene, the main component of turpentine, and then reacted with thiosemicarbazide to obtain (E) ω-formylcamphene thiosemicarbazide 3, which was reacted with 14 α-bromoacetophenone compounds to obtain 14 (E) ω-formylcamphene thiazole hydrazone compounds 5a–5n; the yields were all above 80%. The structures of the target compounds were characterized by IR, ¹H-NMR, ¹³C-NMR, and HR-MS analyses. Then, 500, 250, 125, 62.5, and 31.25 mg/L drug solutions were prepared. Free radical scavenging experiments of 1, 1-diphenyl-2-picrylhydrazyl (DPPH) and 2, 2-bis (3-ethyl-benzothiazole-6-sulfonic acid) diammonium salt (ABTS) were carried out with Trolox and L-ascorbic acid as the control samples. The scavenging… More >

Benkai Shi, Bowen Huang, Huifeng Yang^*, Yongqing Dai, Sijian Chen

Journal of Renewable Materials, Vol.11, No.1, pp. 349-361, 2023, DOI:10.32604/jrm.2023.022343

Abstract To promote the development of timber-concrete composite (TCC) structures, it is necessary to propose the assembly-type connections with high assembly efficiency and shear performances. This article presented the experimental results of the innovative steel-plate connections for TCC beams using prefabricated concrete slabs. The steel-plate connections consisted of the screws and the steel-plates. The steel-plates were partly embedded in the concrete slabs. The concrete slabs and the timber beams were connected by screws through the steel-plates. The parameters researched in this article included screw number, angle steel as the reinforcement for anchoring, and shallow notches on the timber surface to restrict… More >

Sheng He¹, Weiqi Leng^2,*, Yuhe Chen¹, Hongchen Li³, Jingpeng Li¹, Zaixing Wu¹, Zizhang Xiao¹

Journal of Renewable Materials, Vol.11, No.1, pp. 321-331, 2023, DOI:10.32604/jrm.2023.022097

Abstract Microwave (MW) drying method was adopted to enhance the liquid permeability of Scots pine lumber. Structure changes were characterized by stereoscope microscope, scanned electron microscope (SEM) and transmission electron microscope (TEM) examination. Pore parameters before and after MW treatment were detected by mercury intrusion porosimetry (MIP) method, and the effect of structure changes on liquid permeability were analyzed. As stereoscope microscope, SEM and TEM examination results shown, macro and micro checks mainly developed at intercellcular of tracheids, intercellular of ray parenchyma and tracheid, while these checks extend main along the radial-longitudinal plane. Pit border destruction, aspirated pits’ orus translocation and… More >

Junshan Zhao^1,#, Yihan Shi^1,#, Ming Zhang¹, Liu Zhang¹, Xumei Cui¹, Xinghua Zhu², Jitong Su¹, Dandan Jing¹, Dingyu Yang^1,*

Journal of Renewable Materials, Vol.11, No.1, pp. 79-91, 2023, DOI:10.32604/jrm.2023.022030

Abstract In this paper, the non-polluting, non-toxic, and eco-friendly material-MnO₂ electrodes were deposited on three-dimensional porous nickel (Ni) foam by linear sweep voltammetry, and the entire electrodeposition process did not require sintering of the material, which was fast and convenient while avoiding unnecessary energy consumption and thus was environmentally friendly. Scanning electron microscopy (SEM) and transmission electron microscopy were used to examine the surface and microscopic characteristics of each sample (TEM). Chronoamperometry (CA), cyclic voltammetry (CV), galvanostatic charge/discharge (GCD), and electrochemical impedance spectroscopy (EIS) were then used to determine the electrochemical characteristics of the manufactured samples. The result suggests that the… More >

Zongying Fu¹, Yongdong Zhou¹, Tingguo Yan², Yun Lu^1,*

Journal of Renewable Materials, Vol.11, No.1, pp. 93-102, 2023, DOI:10.32604/jrm.2023.021808

Abstract Drying crack is a common phenomenon occurring during moisture discharge from wood, reducing efficient wood utilization. Drying crack is primarily caused by drying stress, and the reasonable methods for determining drying stress are sparse. In this study, the initiation and propagation of cracks during wood discs drying were simulated using the extended finite element method (XFEM). The distribution of drying stress and displacement was analyzed at different crack conditions based on the simulation results. This study aimed to solve the problem of the limitation of drying stress testing methods and provide a new idea for the study of wood drying… More >

Yizhang Wang¹, Zhaoyang Yu¹, Jinbo Hu^1,2,*, Shanshan Chang¹, Yuan Liu¹, Ting Li², Gonggang Liu^1,*, Xiaodong (Alice) Wang³

Journal of Renewable Materials, Vol.11, No.1, pp. 147-165, 2023, DOI:10.32604/jrm.2023.021306

Abstract In this paper, the residue from bamboo factory has been used to design photo-Fenton catalyst, which has the advantages of low cost and magnetic recycling. The photo-Fenton catalytic performance of the biocarbon-based catalyst was excellent and its optimal preparation process was also explored by response surface methodology. First, bamboo-carbon fiber was selected as the photo-Fenton catalyst carrier. Subsequently, the surface of the carbon fiber was modified, with which dopamine, nano-Fe₃O₄ and nano-TiO₂ were successively loaded by hydrothermal method. After examined single factor tests, four factors including dopamine concentration, ferric chloride mass, P25 titanium dioxide mass and liquid-solid ratio were selected… More > Graphic Abstract

Heping Hou¹, Yang Yue^1,*, Jian Liu¹, Darun Xi², Shanhui Liu¹

Journal of Renewable Materials, Vol.11, No.1, pp. 273-289, 2023, DOI:10.32604/jrm.2023.021167

Abstract Environmental contamination has been caused by petroleum-based polymeric materials in the melt deposition process. Nowadays biodegradable materials have been widely used in the fused deposition modeling (FDM) industry, such as polylactic acid (PLA). However, internal complex thermal stress and deformations in part caused by an uneven distribution of PLA filament deposition temperatures during FDM, which will seriously affect the geometric accuracy of the printed part. In order to reduce material waste and environmental pollution during the printing process, the accuracy of PLA part can be improved. Herein, numerical simulation was carried out to investigate the temperature field and stress field… More >

Huimin Huang¹, Zijun Wu², Zhijian Zhou¹, Qiulin Xu¹, Jie Yan^1,*, Qiaoguang Li^1,*

Journal of Renewable Materials, Vol.11, No.1, pp. 257-272, 2023, DOI:10.32604/jrm.2023.021073

Abstract The low utilization rate of pesticides makes the migration of pesticides in water and soil, which brings great harm to the ecosystem. The development of pesticide carriers with good drug loading capacity and release control ability is an effective method to realize effective utilization of pesticides and reduce pesticide losses. In this work, fosthiazate-stearic acid/expanded perlite sustained-release particles were successfully prepared by vacuum impregnation using expanded perlite (EP) as carrier, fosthiazate (FOS) as model pesticide and stearic acid (SA) as hydrophobic matrix. The structure and morphology of the samples were studied by BET, FT-IR, TGA, XRD, DSC and SEM. The… More > Graphic Abstract