Linsen Zhu¹, Jiang Zhou², Xuejun Fan²

CMC-Computers, Materials & Continua, Vol.39, No.2, pp. 113-134, 2014, DOI:10.3970/cmc.2014.039.113

Abstract In this paper, a damage mechanics-based continuum theory is developed for the coupled analysis of moisture vaporization, moisture absorption and desorption, heat conduction, and mechanical stress for a reflow process in microelectronic devices. The extremely compliant film has been used in wafer level lamination process. Such a soft film experiences cohesive rupture subjected to moisture absorption during reflow. The numerical simulation results have demonstrated that vapor pressure due to moisture vaporization is the dominant driving force for the failures. The correlation between the vapor pressure evolution and the film rupture observed from the experiments have been established through two case… More >

S. Liu¹, X. Liu^2,3, Y. Yuan², P. F. He¹, H. A. Mang^2,4

CMC-Computers, Materials & Continua, Vol.39, No.2, pp. 85-112, 2014, DOI:10.3970/cmc.2014.039.085

Abstract Autogenous shrinkage is defined as the bulk deformation of a closed, isothermal, cement-based material system, which is not subjected to external forces. It is associated with the hydration process of the cement paste. From the viewpoint of engineering practice, autogenous shrinkage deformations result in an increase of tensile stresses, which may lead to cracking of early-age concrete. Since concrete is a multi-phase composite with different material compositions and microscopic configurations at different scales, autogenous shrinkage does not only depend on the hydration of the cement paste, but also on the mechanical properties of the constituents and of their distribution. In… More >

Jingguo Yan¹, Xudong Wang¹, Man Yao^1,2, Ning Hu^3,4

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 73-84, 2014, DOI:10.3970/cmc.2014.039.073

Abstract Electronic structure and magnetism of the rare-earth metals Ac and Th doped Fe₃O₄ Fe_1-xRe_xFe_2-yRe_yO₄(Re=Ac, Th; x=0, 0.5, 1; y=0, 0.5, 1.0, 1.5, 2.0) are investigated by first-principle calculations. AcFe₂O₄, FeAc₂O₄ and ThFe₂O₄ are found to be II B-type half-metals. The large bonding-antibonding splitting is believed to be the origin of the gap for AcFe₂O₄, FeAc₂O₄ and ThFe₂O₄, resulting in a net magnetic moment of 9.0μ_B, 4.0μ_B and 8.1μ_B, respectively, compared with 4.0μ_B of Fe₃O₄. Also, the conductance of AcFe₂O₄ and ThFe₂O₄ are both slightly larger than that of Fe3O4. It can be predicted that the new rare-earth half-metals AcFe₂O₄ and… More >

Y.C. Shiah¹, Y.M. Lee², T.C. Huang²

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 49-71, 2014, DOI:10.3970/cmc.2014.039.049

Abstract A common difficulty arises in characterizing the anisotropic properties of a thin sheet of anisotropic material, especially in the transverse direction. This difficulty is even more phenomenal for measuring its mechanical properties on account of its thickness. As the prelude of such investigation, this paper proposes a novel approach to identify the thermal conductivities of an unknown thin layer of anisotropic material. For this purpose, the unknown layer is sandwiched in isotropic materials with known conductivities. Prescribing proper boundary conditions, one may easily measure temperature data on a few sample boundary points. Therefore, the anisotropic thermal conductivities can be calculated… More >

J. Aubry¹, P. Navarro¹, S. Marguet¹, J.-F. Ferrero¹, O. Dorival², L. Sohier³, J.-Y. Cognard³

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 21-47, 2014, DOI:10.3970/cmc.2014.039.021

Abstract In this paper a numerical model dedicated to the simulation of the mechanical behaviour of polymeric Rohacell foams is presented. The finite elements model is developed at the scale of the microstructure idealized by a representative unit cell: the truncated octahedron. Observations made on micrographs of Rohacell lead to mesh this representative unit cell as a lattice of beam elements. Each beam is assigned a brittle linear elastic mechanical behaviour in tension and an elastoplastic behaviour in compression. The plasticity in compression is introduced as a way to mimic the buckling of the edges of the cells observed in experimental… More >

Meng-Kao Yeh¹, Chia-Shien Liu², Chien-Chang Chen³

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 3-20, 2014, DOI:10.3970/cmc.2014.039.003

Abstract The dynamic instability of rectangular graphite/epoxy composite plates under parametric excitation was investigated analytically and experimentally. In analysis, the dynamic system of the composite plate, obtained based on the assumedmodes method, is a general form of Mathieu’s equation, including parametrically excited terms. The instability regions of the system, each separated by two transition curves, were found to be functions of the modal parameters of the composite plate and the position and the excited amplitude of the electromagnetic device on the composite plates. The fiber orientation, the aspect ratio and the layer numbers of the composite plates were varied to assess… More >

Branden B. Kappes¹, Cristian V. Ciobanu²

CMC-Computers, Materials & Continua, Vol.38, No.1, pp. 1-16, 2013, DOI:10.3970/cmc.2013.038.001

Abstract Controlling the bandgap of carbon nanostructures is a key factor in the development of mainstream applications of carbon-based nanoelectronic devices. This is particularly important in the cases where it is desired that the carbon nanostructures are the active elements, as opposed to being the conductive leads between other elements of the device. Here, we report density functional theory calculations of the effect of silicon impurities on the electronic properties of carbon nanotubes (CNTs). We have found that Si adatoms can open up a bandgap in intrinsically metallic CNTs, even when the linear density of Si atoms is low enough that… More >

Yongze Cao¹, Guojian Li¹, Qiang Wang^1,2, Xiaoguang Wang³, Jiaojiao Du¹, Jicheng He¹

CMC-Computers, Materials & Continua, Vol.37, No.3, pp. 195-203, 2013, DOI:10.3970/cmc.2013.037.195

Abstract The Fe₆₀Ni₄₀ (in atomic %) polycrystalline thin films with 90 nm thickness were prepared on 200 °C quartz substrate by using molecular beam vapor deposition method. The influence of 0 T and 6 T magnetic fields on the structural evolution and magnetic properties of thin films was studied by using EDXS, XRD, AFM and VSM. In this study, only α phase was formed in both thin films. It was found that the application of a 6 T magnetic field obviously decreases the RMS of surface roughness and the grain size. For the magnetic properties of the thin films, the 6… More >

L.B. Borkowski¹, K.C. Liu¹, A. Chattopadhyay¹

CMC-Computers, Materials & Continua, Vol.37, No.3, pp. 161-193, 2013, DOI:10.3970/cmc.2013.037.161

Abstract The microstructural variation in fiber-reinforced composites has a direct relationship with its local and global mechanical performance. When micromechanical modeling techniques for unidirectional composites assume a uniform and periodic arrangement of fibers, the bounds and validity of this assumption must be quantified. The goal of this research is to quantify the influence of microstructural randomness on effective homogeneous response and local inelastic behavior. The results indicate that microstructural progression from ordered to disordered decreases the tensile modulus by 5%, increases the shear modulus by 10%, and substantially increases the magnitude of local inelastic fields. The experimental and numerical analyses presented… More >

Ridha Djebali¹, Mohsen Toujani², Bernard Pateyron³

CMC-Computers, Materials & Continua, Vol.37, No.3, pp. 147-160, 2013, DOI:10.3970/cmc.2013.037.147

Abstract In this paper a study of the atmospheric plasma spraying process was conducted. The Jets&Poudres code was used to solve the partial differential equations for the conservation of mass, momentum and energy involved in the problem together with the K-e turbulent model. The Taguchi technique was used to study the influence of processing factors on droplet impact properties obtained on dense zirconia (ZrO₂) under H₂Ar75% plasma gas that allow optimal functioning condition. The test of the operating parameters for the studied ranges showed that the "thermal power" factor plays a key role on the state of sprayed powder. It was… More >