Yuting Liu¹, Hongwei Ding^1,*, Zongshan Wang^1,*, Gaurav Dhiman^2,3,4, Zhijun Yang¹, Peng Hu⁵

CMC-Computers, Materials & Continua, Vol.77, No.2, pp. 2385-2406, 2023, DOI:10.32604/cmc.2023.039883

Abstract The equilibrium optimizer (EO) represents a new, physics-inspired metaheuristic optimization approach that draws inspiration from the principles governing the control of volume-based mixing to achieve dynamic mass equilibrium. Despite its innovative foundation, the EO exhibits certain limitations, including imbalances between exploration and exploitation, the tendency to local optima, and the susceptibility to loss of population diversity. To alleviate these drawbacks, this paper introduces an improved EO that adopts three strategies: adaptive inertia weight, Cauchy mutation, and adaptive sine cosine mechanism, called SCEO. Firstly, a new update formula is conceived by incorporating an adaptive inertia weight to reach an appropriate balance… More >

Zhicheng Liu¹, Long Zhao^1,*, Guanru Wen¹, Peng Yuan², Qiu Jin¹

Structural Durability & Health Monitoring, Vol.17, No.6, pp. 541-555, 2023, DOI:10.32604/sdhm.2023.029760

Abstract The displacement of transmission tower feet can seriously affect the safe operation of the tower, and the accuracy of structural health monitoring methods is limited at the present stage. The application of deep learning method provides new ideas for structural health monitoring of towers, but the current amount of tower vibration fault data is restricted to provide adequate training data for Deep Learning (DL). In this paper, we propose a DT-DL based tower foot displacement monitoring method, which firstly simulates the wind-induced vibration response data of the tower under each fault condition by finite element method. Then the vibration signal… More > Graphic Abstract

Peter Watson¹, Sebastien Vincent Bonnieu², Marcello Lappa^1,*

FDMP-Fluid Dynamics & Materials Processing, Vol.20, No.1, pp. 1-29, 2024, DOI:10.32604/fdmp.2023.029280

Abstract We present a short retrospective review of the existing literature about the dynamics of (dry) granular matter under the effect of vibrations. The main objective is the development of an integrated resource where vital information about past findings and recent discoveries is provided in a single treatment. Special attention is paid to those works where successful synthetic routes to as-yet unknown phenomena were identified. Such landmark results are analyzed, while smoothly blending them with a history of the field and introducing possible categorizations of the prevalent dynamics. Although no classification is perfect, and it is hard to distillate general properties… More >

ELYN AMIELA SALLEH¹, YEONG YEH LEE², ANDEE DZULKARNAEN ZAKARIA³, NUR ASYILLA CHE JALIL⁴, MARAHAINI MUSA^1,*

BIOCELL, Vol.47, No.10, pp. 2233-2244, 2023, DOI:10.32604/biocell.2023.030541

Abstract Colorectal cancer (CRC) is a major global health concern. Accumulation of cancer-associated fibroblasts (CAFs) in CRC is associated with poor prognosis and disease recurrence. CAFs are the main cellular component of the tumor microenvironment. CAF-tumor cell interplay, which is facilitated by various secretomes, drives colorectal carcinogenesis. The complexity of CAF populations contributes to the heterogeneity of CRC and influences patient survival and treatment response. Due to their significant roles in colorectal carcinogenesis, different clinical applications utilizing or targeting CAFs have been suggested. Circulating CAFs (cCAFs) which can be detected in blood samples, have been proposed to help in determining patient… More > Graphic Abstract

Baohua Li¹, Yuanjun Dai^1,2,*, Jingan Cui¹, Cong Wang¹, Kunju Shi¹

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.12, pp. 3033-3043, 2023, DOI:10.32604/fdmp.2023.029583

Abstract To reduce the vibration and aerodynamic noise of wind turbines, a new design is proposed relying on a blade with a bifurcated apex or tip. The performances of this wind turbine wheel are tested at the entrance of a DC (directaction) wind tunnel for different blade tip angles and varying centrifugal force and aerodynamic loads. The test results indicate that the bifurcated apex can reduce the vibration acceleration amplitude and the vibration frequency of the wind wheel. At the same time, the bifurcated apex can lower the maximum sound pressure level corresponding to the rotating fundamental frequency of the wind… More >

Youhao Wang¹, Chuntian Zhe¹, Chang Guo², Jinpeng Li³, Jinheng Li³, Shen Cheng², Zitian Wu¹, Suoying He¹, Ming Gao^1,*

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.12, pp. 2965-2980, 2023, DOI:10.32604/fdmp.2023.029292

Abstract Flow channels with a variable cross-section are important components of piping system and are widely used in various fields of engineering. Using a finite element method and modal analysis theory, flow-induced noise, mode shapes, and structure-borne noise in such systems are investigated in this study. The results demonstrate that the maximum displacement and equivalent stress are located in the part with variable cross-sectional area. The average excitation force on the flow channel wall increases with the flow velocity. The maximum excitation force occurs in the range of 0–20 Hz, and then it decreases gradually in the range of 20–1000 Hz.… More >

Dongmei Huang¹, Dang Hong², Wei Li^1,*, Guidong Yang¹, Vesna Rajic³

CMES-Computer Modeling in Engineering & Sciences, Vol.138, No.1, pp. 509-524, 2024, DOI:10.32604/cmes.2023.029215

Abstract In this paper, the bifurcation properties of the vibro-impact systems with an uncertain parameter under the impulse and harmonic excitations are investigated. Firstly, by means of the orthogonal polynomial approximation (OPA) method, the nonlinear damping and stiffness are expanded into the linear combination of the state variable. The condition for the appearance of the vibro-impact phenomenon is to be transformed based on the calculation of the mean value. Afterwards, the stochastic vibro-impact system can be turned into an equivalent high-dimensional deterministic non-smooth system. Two different Poincaré sections are chosen to analyze the bifurcation properties and the impact numbers are identified… More >

Xiaofang Kang^1,*, Jian Wu¹, Xinqi Wang¹, Shancheng Lei²

CMES-Computer Modeling in Engineering & Sciences, Vol.138, No.1, pp. 551-593, 2024, DOI:10.32604/cmes.2023.029044

Abstract In order to improve the seismic performance of adjacent buildings, two types of tuned inerter damper (TID) damping systems for adjacent buildings are proposed, which are composed of springs, inerter devices and dampers in serial or in parallel. The dynamic equations of TID adjacent building damping systems were derived, and the H₂ norm criterion was used to optimize and adjust them, so that the system had the optimum damping performance under white noise random excitation. Taking TID frequency ratio and damping ratio as optimization parameters, the optimum analytical solutions of the displacement frequency response of the undamped structure under white… More > Graphic Abstract

Chun Sha^1,*, Chaohui Yue², Wenchen Wang³

Structural Durability & Health Monitoring, Vol.17, No.5, pp. 369-381, 2023, DOI:10.32604/sdhm.2023.027948

Abstract Convolution neural networks in deep learning can solve the problem of damage identification based on vibration acceleration. By combining multiple 1D DenseNet submodels, a new ensemble learning method is proposed to improve identification accuracy. 1D DenseNet is built using standard 1D CNN and DenseNet basic blocks, and the acceleration data obtained from multiple sampling points is brought into the 1D DenseNet training to generate submodels after offset sampling. When using submodels for damage identification, the voting method ideas in ensemble learning are used to vote on the results of each submodel, and then vote centrally. Finally, the cantilever damage problem… More >

Zhen Zhong^*, Yadong Li, Yuxuan Zhao, Pengfei Ju

Sound & Vibration, Vol.57, pp. 15-27, 2023, DOI:10.32604/sv.2023.041954

Abstract Bent-housing motor is the most widely used directional drilling tool, but it often encounters the problem of high friction when sliding drilling in horizontal wells. In this paper, a mathematical model is proposed to simulate slide drilling with a friction reduction tool of axial vibration. A term called dynamic effective tractoring force (DETF) is defined and used to evaluate friction reduction effectiveness. The factors influencing the DETF are studied, and the tool placement optimization problem is investigated. The study finds that the drilling rate of penetration (ROP) can lower the DETF but does not change the trend of the DETF… More >