Amir Reza Ansari Dezfoli¹, Weng-Sing Hwang^1,2

CMC-Computers, Materials & Continua, Vol.49-50, No.1, pp. 1-11, 2015, DOI:10.3970/cmc.2015.049.001

Abstract Investigations of the microstructural evolution of Titanium (Ti) alloys during high temperature processes and heat treatment are attracting more attention due to wide variety of applications for such alloys. In most of these processes the Titanium alloys are subjected to fast heating or cooling rates. In this paper, Monte Carlo simulation is used to simulate the grain growth kinetics of Ti-6Al-4V alloy during fast heat treatment. Here, Monte Carlo simulation of grain growth is based on the Q-state Potts model. Our model is calibrated using the parabolic grain growth law, dⁿ-d₀ⁿ = kt, where the empirical constants are taken… More >

Yanbin Wang^1,2, Deli Gao¹, Jun Fang¹

CMC-Computers, Materials & Continua, Vol.48, No.1, pp. 25-42, 2015, DOI:10.3970/cmc.2015.048.025

Abstract In this paper, the buckling and collapse analysis of offshore pipeline under combined tension, bending moment, and external pressure has been presented with theoretical analysis and FE (finite element) simulation method respectively. Based on the model initially proposed by Kyriakides, a 2-D theoretical model has been further developed. To verify the correctness and accuracy of the model proposed in this paper, numerical simulations have been conducted with 3-D FE model using ABAQUS software. Good consistency has been shown between the calculation results which validate the availability of the theoretical analysis. On this basis, the influence of load path, material properties,… More >

Bui Duc Thuan^1,2, Wong Yonghui², Chua Kian Jon², Ng Kim Choon²

CMC-Computers, Materials & Continua, Vol.47, No.2, pp. 89-105, 2015, DOI:10.3970/cmc.2015.047.089

Abstract The cup method and dynamic moisture permeation cell (DMPC) method are two common techniques used to determine the water vapor permeation properties of a membrane. Often, ignoring the resistance of boundary air layers to the transport of water vapor results in the water vapor permeance of the membrane being underestimated in practical tests. The measurement errors are higher with highly permeable membranes. In this study, the two methods were simulated using COMSOL Multiphysics platform and the extent of the error was evaluated. Initial results showed that the error is equally high in both methods. With the correction for the still… More >

V. G. Yakhno¹, B. Çiçek²

CMC-Computers, Materials & Continua, Vol.44, No.3, pp. 141-166, 2014, DOI:10.3970/cmc.2014.044.141

Abstract A method for an approximate computation of the electric and magnetic Green’s functions for the time-harmonic Maxwell’s equations in the general electrically gyrotropic materials is proposed. This method is based on the Fourier transform meta-approach: the equations for electric and magnetic fields are written in terms of images of the Fourier transform with respect to space variables and as a result of it the linear algebraic systems for finding Fourier images of the columns of the Green’s functions are obtained. The explicit formulas for the solutions of the obtained systems have been found. Finally, elements of the Green’s functions are… More >

F. Marín¹, F. Alhama¹, J.A. Moreno¹

CMC-Computers, Materials & Continua, Vol.43, No.1, pp. 1-20, 2014, DOI:10.3970/cmc.2014.043.001

Abstract The field of nanotribology in the last decades was established through the introduction of Atomic Force/Friction Force Microscopes. However, our theoretical understanding of the individual processes involved in friction force microscopy is limited. This work designs a reliable and efficient model for the stickslip phenomenon, following the rules of network simulation. The model is able to manage different types of potential between the tip and the sample surface, allowing different kinds of sample material and microscope tip properties to be simulated with only minor changes in the code. The most analysed tribological materials in technical literature are simulated to test… More >

S. Zhao¹, Zichun Yang^1,2, X. G. Zhou³, X. Z. Ling⁴, L. S. Mora⁵, D. Khoshkhou⁶, J. Marrow⁵

CMC-Computers, Materials & Continua, Vol.42, No.2, pp. 103-124, 2014, DOI:10.3970/cmc.2014.042.103

Abstract Continuous SiC fiber reinforced SiC matrix composites (SiC/SiC) have been studied and developed for high temperature and fusion applications. Polymer impregnation and pyrolysis (PIP) is a conventional technique for fabricating SiC/SiC composites. In this research, KD-1 SiC fibers were employed as reinforcements, a series of coatings such as pyrocarbon (PyC), SiC and carbon nanotubes (CNTs) were synthesized as interphases, PCS and LPVCS were used as precursors and SiC/SiC composites were prepared via the PIP method. The mechanical properties of the SiC/SiC composites were characterized. Relationship between the interphase shear strength and the fracture toughness of the composites was established. X-ray… More >

Leiting Dong^1,2, Salah H. Gamal³, Satya N. Atluri^2,4

CMC-Computers, Materials & Continua, Vol.37, No.1, pp. 1-21, 2013, DOI:10.3970/cmc.2013.037.001

Abstract In this paper, a simple and reliable procedure of stochastic computation is combined with the highly accurate and efficient Trefftz Computational Grains (TCG), for a direct numerical simulation (DNS) of heterogeneous materials with microscopic randomness. Material properties of each material phase, and geometrical properties such as particles sizes and distribution, are considered to be stochastic with either a uniform or normal probabilistic distributions. The objective here is to determine how this microscopic randomness propagates to the macroscopic scale, and affects the stochastic characteristics of macroscopic material properties. Four steps are included in this procedure: (1) using the Latin hypercube sampling,… More >

J.W. Chen¹, W. Liu¹, X.Y. Su^1,2

CMC-Computers, Materials & Continua, Vol.24, No.2, pp. 163-182, 2011, DOI:10.3970/cmc.2011.024.163

Abstract Truss-core sandwich plates are thin-walled structures comprising a truss core and two thin flat sheets. Since no direct analytical solution for the dynamic response of such structures exists, the complex three dimensional (3D) systems are idealized as equivalent 2D homogeneous continuous plates. The macroscopic effective bending and transverse shear stiffness are derived. Two representative core topologies are considered: pyramidal truss core and tetrahedral truss core. The first order shear deformation theory is used to study the flexural vibration of a simply supported sandwich plate. The buckling of the truss core plate on an elastic foundation subjected to biaxial in-plane compressive… More >

Xiaozhi Tang¹, Yafang Guo¹, Yu Gao¹

CMC-Computers, Materials & Continua, Vol.23, No.1, pp. 1-8, 2011, DOI:10.3970/cmc.2011.023.001

Abstract Atomistic simulations were performed to study the nanoindentation for two kinds of FCC metals, aluminum and copper. Due to the higher stacking faults in aluminum than in copper, two different deformation mechanisms were observed in our simulation under exactly the same simulation condition. Aluminum and copper also showed different mechanical properties in the unloading stage. The influence of stacking sequence along the loading direction on deformation mechanism was also investigated in this paper. More >

Yong Kou¹, Ke Jin¹, Xiaojing Zheng^1,2

CMC-Computers, Materials & Continua, Vol.22, No.2, pp. 129-146, 2011, DOI:10.3970/cmc.2011.022.129

Abstract Magnetic shielding needs to be employed to ensure proper operation of some electronic equipment which are sensitive to external magnetic interference, such as cryogenic valves located inside the ITER feeder cubicles. This paper is concerned with the shielding efficiency of the magnetic shielding enclosures. A 3-D theoretical model for Fe-Ni alloy magnetic shielding enclosures based on finite element method (FEM) is obtained with the nonlinear law of magnetization. The influence of shielding materials, enclosure configurations, single or multi- layer designs, and apertures on the shielding efficiency is investigated. It is shown that the proposed model can predict the shielding efficiency… More >