M.R. Khoshravan¹ and M.A. Setoodeh¹

CMC-Computers, Materials & Continua, Vol.16, No.3, pp. 195-228, 2010, DOI:10.3970/cmc.2010.016.195

Abstract The use of welding to permanently join plates is common in industry due to its high efficiency. But welding creates thermal stresses, which can lead to residual stresses and physical distortion. This phenomenon directly influences the buckling stiffness of the welded structure. The welding distortion not only makes difficult the erection of the project, but also influences the final quality and cost of production. In this research, the thermo-elastic-plastic conditions were simulated by a three-dimensional (3D) finite element model (FE). Mechanical and thermal properties of the material were applied to the model, leading to eigenvalue analysis of the thermal and… More >

Xiaohua Hu¹, Gordana A. Cingara¹, David S. Wilkinson¹, Mukesh Jain², PeidongWu², Raja K. Mishra³

CMC-Computers, Materials & Continua, Vol.14, No.2, pp. 99-124, 2009, DOI:10.3970/cmc.2009.014.099

Abstract This work aims to understand the texture distribution in the localized necking band formed during uni-axial tension of AA5754 using an edge-constrained, plane strain post-necking FE model. The model domain is a long cross section of the band. Initial grain structure is mapped into the mesh from EBSD data using a modified Voroni-cell interpolation and considering pre-straining prior to localized necking. The material points in grains are assumed to exhibit isotropic elastoplastic behavior but have a relative strength in terms of Taylor factors which are updated by a Taylor-Bishop-Hill model. The predicted textures and gradients within the localized necking band… More >

Dyi-Cheng¹, Syuan-Yi Syong¹

CMC-Computers, Materials & Continua, Vol.13, No.3, pp. 191-200, 2009, DOI:10.3970/cmc.2009.013.191

Abstract Finite element simulations are performed to investigate the plastic deformation behavior of Ti-6Al-4V titanium alloy during its indirect extrusion through a four-hole die. The simulations assume the die, mandrel and container to be rigid bodies and ignore the temperature change induced during the extrusion process. Under various extrusion conditions, the present numerical analysis investigates the effective stress and profile of product at the exit. The relative influences of the friction factors, the temperature of billet and the eccentricity of four-hole displacement are systematically examined. The simulations focus specifically on the effects of the friction factor, billet temperature and eccentricity ratio… More >

S.H. Kwon¹, H.K. Lee²

CMC-Computers, Materials & Continua, Vol.12, No.3, pp. 197-222, 2009, DOI:10.3970/cmc.2009.012.197

Abstract The electromagnetic shielding effectiveness of steel fiber-reinforced mortar was numerically examined in this study. A series of numerical analysis on twenty-seven types of specimens of different diameters, lengths, and volume fractions of fibers were conducted using the FE program HFSS to investigate the effect of the dimensions of steel fibers and the amount of fibers added to the mortar on the shielding effectiveness. S-parameters of some specimens were experimentally measured by the free space method and the experimentally measured S-parameters were compared with those computed in order to verify the present numerical analysis method. It was found that smaller diameters… More >

Amiya K. Samanta¹, Somnath Ghosh²

CMC-Computers, Materials & Continua, Vol.12, No.1, pp. 1-38, 2009, DOI:10.3970/cmc.2009.012.001

Abstract This paper presents a formulation of hypo-elasticity based RC beam model with bond-slip. Details of the constitutive model and analysis method used are provided. A procedure has been described to carry out three-dimensional analysis considering both geometrical as well as material nonlinearity for a simply supported RC beam employing finite element technique, which uses 8-noded isoparametric hexahedral element HCiS18. Enhanced assumed strain (EAS) formulation has been utilized to predict load-deformation and internal stresses both in the elastic as well as nonlinear regime. It models the composite behaviour of concrete and reinforcements in rigid /perfect bond situation and their mutual interaction… More >

Chyanbin Hwu¹, T.L. Kuo, Y.C. Chen

CMC-Computers, Materials & Continua, Vol.11, No.3, pp. 165-184, 2009, DOI:10.3970/cmc.2009.011.165

Abstract In this paper the near tip solutions for interface corners written in terms of the stress intensity factors are presented in a unified expression. This single expression is applicable for any kinds of interface corners including corners and cracks in homogeneous materials as well as interface corners and interface cracks lying between two dissimilar materials, in which the materials can be any kinds of linear elastic anisotropic materials or piezoelectric materials. Through this unified expression of near tip solutions, the singular orders of stresses and their associated stress/electric intensity factors for different kinds of interface problems can be determined through… More >

D. S. Liu¹, C. Y. Tsai¹, S. R. Lyu²

CMC-Computers, Materials & Continua, Vol.11, No.2, pp. 147-164, 2009, DOI:10.3970/cmc.2009.011.147

Abstract This study presents a novel numerical method for extracting the tempe -rature-dependent mechanical properties of the gold and aluminum thin-films. In the proposed approach, molecular dynamics (MD) simulations are performed to establish the load-displacement response of the thin substrate nanoindented at temperatures ranging from 300-900 K. A simple but effective procedure involving genetic algorithm (GA) and finite element method (FEM) is implemented to extract the material constants of the gold and aluminum substrates. The material constants are then used to construct the corresponding stress-strain curve, from which the elastic modulus, yield stress and the tangent modulus of the thin film… More >

Ching-Chi Hsu¹, Jinn Lin², Yongyut Amaritsakul³, Takalamesar Antonius³, Ching-Kong Chao^3,4

CMC-Computers, Materials & Continua, Vol.11, No.1, pp. 1-14, 2009, DOI:10.3970/cmc.2009.011.001

Abstract Dynamic hip screw and gamma nail have been widely used to treat the patients with proximal femoral fractures, but clinical failures of those implants are still to be found. This study developed three-dimensional finite element models to investigate the biomechanical performances of the implants. Two kinds of commercially available implants (dynamic hip screw and gamma nail) and one newly designed implant (double screw nail) under three kinds of the proximal femoral fractures (neck fracture, subtrochanteric fracture, and subtrochanteric fracture with gap) were evaluated. Double screw nail showed better biomechanical performances than dynamic hip screw and gamma nail. Two commercially available… More >

T. Nishioka¹, S. Tchouikov¹, T. Fujimoto¹

CMC-Computers, Materials & Continua, Vol.3, No.3, pp. 147-154, 2006, DOI:10.3970/cmc.2006.003.147

Abstract In this study, phenomena of multiple branching of dynamically propagating crack are investigated numerically. The complicated paths of cracks propagating in a material are simulated by moving finite element method based on Delaunay automatic triangulation (MFEM BODAT), which was extended for such problems. For evaluation of fracture parameters for propagating and branching cracks switching method of the path independent dynamic J integral was used. Using these techniques the generation phase simulation of multiple dynamic crack branching was performed. Various dynamic fracture parameters, which are almost impossible to obtain by experimental technique alone, were accurately evaluated. More >

Hamid Sharifi¹ and Augustin Gakwaya¹

CMC-Computers, Materials & Continua, Vol.3, No.2, pp. 77-96, 2006, DOI:10.3970/cmc.2006.003.077

Abstract In this paper, an object-oriented modeling of solid material constitutive behavior using the UML notation is presented. Material properties are first classified into large and small deformation kinematical models. In the small deformation package, we keep classes such as Elastic, ElastoPlastic, ViscoElastic and ViscoPlastic. In the large deformation package, we store classes such as ElastoPlastic, HyperElastic, HyperPlastic, HyperViscoElastic, HyperViscoPlastic and so on. The hierarchical structure, the association relationships as well as key attributes and methods of these classes are presented. We used a C++ implementation of the above model for developing HyperElastic, HyperElastoPlastic and Contact applications in the Diffpack environment. More >