Yidong Bao^1,2, Dongmei Wu^1,3

CMES-Computer Modeling in Engineering & Sciences, Vol.100, No.4, pp. 277-294, 2014, DOI:10.3970/cmes.2014.100.277

Abstract Aiming at the shortcomings of mass-spring model, this paper, on the basis of preliminary studies, established a new viscoelastic soft tissue model based on meshless structure. The model is consisted of a large quantity of filled spheres, with every three spheres being connected by a spring and a Kelvin structure, which can further enhance the real-time virtual simulation operability while ensure the viscoelasticity of basic model. The stress relaxation and creep equation of the model can be derived from formula derivation. Through setting different parameters to the filled spheres, this model, with certain universal property, can create a virtual liver,… More >

Chein-Shan Liu¹, Chung-Lun Kuo²

CMES-Computer Modeling in Engineering & Sciences, Vol.77, No.1, pp. 57-80, 2011, DOI:10.3970/cmes.2011.077.057

Abstract In this paper, the solutions of inverse Cauchy problems for quasi-linear elliptic equations are resorted to an unusual mixed group-preserving scheme (MGPS). The bottom of a finite rectangle is imposed by overspecified boundary data, and we seek unknown data on the top side. The spring-damping regularization method (SDRM) is introduced by converting the governing equation into a new one, which includes a spring term and a damping term. The SDRM can further stabilize the inverse Cauchy problems, such that we can apply a direct numerical integration method to solve them by using the MGPS. Several numerical examples are examined to… More >

Masato Saitoh¹

CMES-Computer Modeling in Engineering & Sciences, Vol.67, No.3, pp. 211-238, 2010, DOI:10.3970/cmes.2010.067.211

Abstract This paper describes the transformation of impedance functions in general structural systems with non-classical damping into a one-dimensional spring-dashpot system (1DSD). A transformation procedure based on complex modal analysis is proposed, where the impedance function is transformed into a 1DSD comprising units arranged in series. Each unit is a parallel system composed of a spring, a dashpot, and a unit having a spring and a dashpot arranged in series. Three application examples are presented to verify the applicability of the proposed procedure and the accuracy of the 1DSDs. The results indicate that the 1DSDs accurately simulate the impedance functions for… More >

L. Távara¹, V. Manticˇ ¹, E. Graciani¹, J. Cañas¹, F. París¹

CMES-Computer Modeling in Engineering & Sciences, Vol.58, No.3, pp. 247-270, 2010, DOI:10.3970/cmes.2010.058.247

Abstract The problem of a crack in a thin adhesive layer is considered. The adherents may have orthotropic elastic behavior which allows composite laminates to be modeled. In the present work a linear elastic-brittle constitutive law of the thin adhesive layer, called weak interface model, is adopted, allowing an easy modeling of crack propagation along it. In this law, the normal and tangential stresses across the undamaged interface are proportional to the relative normal and tangential displacements, respectively. Interface crack propagation is modeled by successive breaking of the springs used to discretize the weak interface. An important feature of the BEM… More >

Sudib K. Mishra¹, J. K. Paik², S. N. Atluri¹

CMES-Computer Modeling in Engineering & Sciences, Vol.50, No.1, pp. 67-96, 2009, DOI:10.3970/cmes.2009.050.067

Abstract We present a simulation based study, by combining several models involving multiple time scales and physical processes, which govern the interfacial stress corrosion cracking (SCC) in grain boundaries, layered composites or bi-materials, and the mechanisms of inhibition using `smart' agents. The inhibiting agents described herein, automatically sense the initiation of damage, migrate to the sites and delay the corrosion kinetics involved in the process. The phenomenon of SCC is simulated using the lattice spring model (for the mechanical stresses), coupled with a finite difference model of diffusing species, causing the dissolution of the interfacial bonds. The dissolution is expressed through… More >

I-L. Chang¹, M.-S. Yeh¹

CMES-Computer Modeling in Engineering & Sciences, Vol.41, No.2, pp. 95-106, 2009, DOI:10.3970/cmes.2009.041.095

Abstract One-dimensional copper nanospring with elliptic cross section was studied using molecular statics method based on minimum energy consideration. Various geometric sizes (wire semi-axis length, radius, pitch) and crystal orientations of nanosprings were systematically modeled to investigate the size dependence of elastic properties for both normal and binormal nanosprings. It was observed that as the wire semi-axis increases, and the radius and pitch decrease, the nanospring stiffness would increase irrespective to the crystal orientations. Moreover, it was noticed that the normal nanosprings always behave stiffer than the binormal ones for the same radius, pitch and cross-sectional geometry in our study. More >

D. S. Sophianopoulos¹, G. T. Michaltsos²

CMES-Computer Modeling in Engineering & Sciences, Vol.2, No.1, pp. 15-26, 2001, DOI:10.3970/cmes.2001.002.015

Abstract The present work deals with the global stability aspects of a simple two-degrees-of-freedom autonomous initially imperfect damped model, under step (conservative) loading. The proposed system is an extension of the classical limit point one firstly introduced by von Mises, with the addition of a linear rotational spring. The effect of its properties (stiffness and damping) are fully assessed and under certain combinations of the parameters involved a third possibility of postbuckling dynamic response is revealed. This is associated with a point attractor response on a stable prebuckling fixed point, although dynamic buckling has already occurred, a finding validating new relevant… More >

S. K. Panthi^1,2, N. Ramakrishnan², K. K. Pathak², J. S. Chouhan³

CMC-Computers, Materials & Continua, Vol.6, No.1, pp. 13-20, 2007, DOI:10.3970/cmc.2007.006.013

Abstract One of the important features of flanging process is elastic recovery during unloading leading to springback. The elastic recovery is associated with various tool and material parameters. It is difficult to analytically predict the elastic recovery accurately owing to the complex material deformation behavior. In this investigation, a commercially available Finite Element software is used for elasto-plastic analysis of flanging process. The springback is studied varying geometrical, material and friction parameters. The results of the simulation are validated with a few published experimental results. More >

Xiaorui Zhang^1,2,3,*, Jiali Duan¹, Jia Liu², Norman I. Badler³

CMC-Computers, Materials & Continua, Vol.60, No.3, pp. 1055-1071, 2019, DOI:10.32604/cmc.2019.03915

Abstract Current research on suture simulation mainly focus on the construction of suture line, and existing suture simulation systems still need to be improved in terms of diversity, soft tissue effects, and stability. This paper presents an integrated liver suture surgery system composed of three consecutive suture circumstances, which is conducive to liver suture surgery training. The physically-based models used in this simulation are based on different mass-spring models regulated by a special constrained algorithm, which can improve the model accuracy, and stability by appropriately restraining the activity sphere of the surrounding mass nodes around the suture points. We also studied… More >

Xiaorui Zhang^1,3,*, Jiali Duan¹, Lifeng Zhu², Ladislav Kavan³

CMC-Computers, Materials & Continua, Vol.57, No.3, pp. 505-519, 2018, DOI:10.32604/cmc.2018.01842

Abstract Puncture is a common operation in surgery, which involves all kinds of tissue materials with different geometry and mechanical properties. As a new cross-disciplinary research area, Virtual Surgery (VS) makes simulation of soft tissue in puncture operation possible in virtual environment. In this paper, we introduce a VS-based puncture system composed by three-layer soft tissue, simulated with spherical harmonic function (SHF), which is covered with a force mesh, constructed by mass spring model (MSM). The two models are combined together with a parameter of SHF named surface radius, which provides MSM with real-time deformation data needed in force calculation. Meanwhile,… More >