Meriem Fehri^1,2, Rachid Robleh Ragueh¹, Alexandre Vivet^1*, Fakhreddine Dammak², Mohamed Haddar²

Journal of Renewable Materials, Vol.5, No.1, pp. 38-47, 2017, DOI:10.7569/JRM.2016.634123

Abstract The purpose of this work is the improvement of flax fiber-reinforced composites obtained by vacuum molding in order to encourage their insertion into industrial products. The relatively high degree of porosity in these kinds of composites, due to the lack of compatibility between epoxy matrix and flax fibers and the hydrophilicity of flax fiber, remains a major constraint to their use in the industrial world. Hence, we have used a combination of carbon fibers with those of flax in order to optimize the properties of the assembly. Several stacking sequences have been tested in order to analyze the influence of… More >

Miguel Ángel Ramírez¹, Patricia González², Juan Reinerio Fagundo², Margaret Suarez³, Clara Melian³, Tania Rodríguez¹, Carlos Peniche^4*

Journal of Renewable Materials, Vol.5, No.1, pp. 30-37, 2017, DOI:10.7569/JRM.2016.634121

Abstract The inorganic components of crustacean shells are usually removed using HCl solutions. This provokes undesirable modifications in the extracted chitin. In the present procedure, deproteinized lobster shells were demineralized with CO2 and a cationic resin (cationite). The resulting chitin (CHI-CO2) is compared in terms of degree of acetylation (DA), crystallinity index (CrI) and thermal stability with chitins obtained by demineralization procedures with HCl (CHI-HCl) and ethylenediaminetetraacetic acid (CHI-EDTA). The ash content of chitins demineralized with CO2 was similar to that of chitins prepared using HCl or EDTA. However, the resultant DA and CrI of CHI-HCl and CHI-EDTA were lower than… More >

M. Thébault^1,2, A. Pizzi1^3*, F.J. Santiago-Medina¹, F.M. Al-Marzouki³, S. Abdalla³

Journal of Renewable Materials, Vol.5, No.1, pp. 21-29, 2017, DOI:10.7569/JRM.2016.634116

Abstract Isocyanate-free polyurethane resins biosourced to a very high percentage level were prepared by the reaction of aminated mimosa tannin extract with commercial mimosa tannin extract prereacted with dimethyl carbonate. The reaction took place with ease at ambient temperature. Indications were that the polyurethanes obtained formed a hard film when cured at a temperature higher than 100 °C. Furthermore, the carbohydrate fraction of the tannin extract also appeared to be carbonated and reacted to generate isocyanate-free polyurethane linkages with the aminated tannins. This indicated that not only the polyphenolic fraction of the tannin extract, but also its other major component, can… More >

Mehdi Tajvidi^1*, Douglas J. Gardner², Douglas W. Bousfield³

Journal of Renewable Materials, Vol.4, No.5, pp. 365-376, 2016, DOI:10.7569/JRM.2016.634103

Abstract A novel application of cellulose nanomaterials, particularly cellulose nanofibrils (CNF) as a binder in conventional and novel laminate and particulate composite systems is discussed. Using cellulose nanomaterials as a reinforcing agent in conventional polymer composites faces several difficulties: 1) there are no easy ways to dry the CNF and maintain nanoscale dimensions, 2) there are compatibility issues related to cellulose-polymer bonding, and 3) there are issues related to obtaining a good distribution and redispersion of nanoscale materials inside a polymer matrix. An alternative strategy is applications in which cellulose nanomaterials can be used in the aqueous suspension form without first… More >

Jithin Joy^1,2,3, Cintil Jose³, Srirama B. Varanasi⁴, Lovely Mathew P.^2,3, Sabu Thomas², Srikanth Pilla^1,5*

Journal of Renewable Materials, Vol.4, No.5, pp. 351-364, 2016, DOI:10.7569/JRM.2016.634128

Abstract Isora nanofibers (INF) were produced by a combined thermal-chemical-mechanical method from Helicteres isora plant. The resulting fibers were analyzed using transmission electron microscopy and scanning electron microscopy, which showed a network-like structure with a length of 600 nm, width of 50 nm and an aspect ratio of 12. Fourier transform infrared spectroscopy indicated that chemical treatments progressively removed noncellulosic constituents. X-ray diffraction analysis revealed that crystallinity increased with successive chemical treatments. Using the synthesized isora nanofibers, poly(butylene succinate) (PBS)-based biodegradable nanocomposites were prepared. The nanocomposites were processed using a Brabender twin-screw compounder and an injection molding machine. Effects of INF… More >

Nicole M. Stark

Journal of Renewable Materials, Vol.4, No.5, pp. 313-326, 2016, DOI:10.7569/JRM.2016.634115

Abstract Performance requirements for packaging films may include barrier properties, transparency, flexibility, and tensile strength. Conventional packaging materials, such as plastic films and laminates, are typically made from petroleum-based polymers. Currently, there is a drive to develop sustainable packaging materials. These alternative materials must be able to be manufactured economically and on a commercial scale, exhibit barrier properties and transparency, and provide adequate mechanical performance. As a biobased, renewable material, cellulose nanomaterials (CNs) are ideally suited to be used in sustainable packaging applications. CNs include cellulose nanocrystals (CNCs) and cellulose nanofibrils (CNFs) and each can provide benefit to packaging films. Manufactured… More >

Ronald Sabo^1*, Aleksey Yermakov², Chiu Tai Law³, Rani Elhajjar⁴

Journal of Renewable Materials, Vol.4, No.5, pp. 297-312, 2016, DOI:10.7569/JRM.2016.634114

Abstract Cellulose nanomaterials have a number of interesting and unique properties that make them well-suited for use in electronics applications such as energy harvesting devices, actuators and sensors. Cellulose nanofibrils and nanocrystals have good mechanical properties, high transparency, and low coefficient of thermal expansion, among other properties that facilitate both active and inactive roles in electronics and related devices. For example, these nanomaterials have been demonstrated to operate as substrates for flexible electronics and displays, to improve the efficiency of photovoltaics, to work as a component of magnetostrictive composites and to act as a suitable lithium ion battery separator membrane. A… More >

Facundo I. Altuna¹, Borja Fernández-d’Arlas², M. Angeles Corcuera², Arantxa Eceiza², Mirta I. Aranguren³, Pablo M. Stefani^3*

Journal of Renewable Materials, Vol.4, No.4, pp. 275-284, 2016, DOI:10.7569/JRM.2016.634120

Abstract Mixtures of biomass-derived polyols were used to synthesize rigid polyurethane (PU) foams. A commercial polymerized methylene diphenyl diisocyanate (pMDI) was used as crosslinker, and distilled water served as foaming agent. The morphology and mechanical properties of foams with different glycerol and water contents were compared in order to evaluate the most suitable formulations. The rigid foams with higher water contents had larger and more anisotropic cells, explaining their lower density. Compressive moduli ranged from about 2.5 MPa to above 20 MPa and collapse stresses from 55 kPa to more than 1 MPa for densities between 54 and 143 kg/m3. Densification… More >

M. L. Lambri^1,2, E. D. Giordano^2,3, P. B. Bozzano⁴, F. G. Bonifacich², J. I. Pérez-Landazábal^5,6, G. I. Zelada², D. Gargicevich², V. Recarte^5,6, O. A. Lambri^2*

Journal of Renewable Materials, Vol.4, No.4, pp. 251-257, 2016, DOI:10.7569/JRM.2016.634111

Abstract The denaturation processes of collagen in the temperature range between 450 K and 670 K are revealed through studies performed on cow rib bones by means of mechanical spectroscopy, differential scanning calorimetry, thermogravimetry, scanning electron microscopy and infrared spectroscopy. The conformational change of the collagen molecules from a triple helix structure to a random coil was found at around 510 K. It was determined that the transformation is developed through the viscous movement of fibrils with an activation energy of (127 ± 8) kJ/mol. The second stage of massive bulk deterioration of the collagen was found at around 600 K,… More >

Oscar F. Aguilar Gutierrez, Alejandro D. Rey^*

Journal of Renewable Materials, Vol.4, No.4, pp. 241-250, 2016, DOI:10.7569/JRM.2016.634119

Abstract Biological plywoods are solid analogues of liquid crystalline phases whose building blocks, including cellulose, collagen and chitin, present multifunctionality, providing in some cases protection, camouflage, self-healing and/or adaptability to the surrounding environment. The 3D ordered structure is the main factor for these fascinating properties, and the assessment of the structure-property relationship will be a powerful tool in terms of future material design and innovation. Cross-section observations lead to characteristic patterns depending on the specific arrangement of the plywood’s building blocks. Twisted plywood architectures, known as the Bouligand structure, lead to the widely observed arced patterns which can be ideal or… More >