Yashan Feng¹, Yafang Tian¹, Yongxin Yang¹, Yufang Zhang¹, Haiwei Guo¹, Jing’an Li^2,*

CMC-Computers, Materials & Continua, Vol.79, No.1, pp. 263-278, 2024, DOI:10.32604/cmc.2024.047004 - 25 April 2024

Abstract Electroactive anticorrosion coatings are specialized surface treatments that prevent or minimize corrosion. The study employs strategic thermodynamic equilibrium calculations to pioneer a novel factor in corrosion protection. A first-time proposal, the total acidity (TA) potential of the hydrogen (pH) concept significantly shapes medical magnesium alloys. These coatings are meticulously designed for robust corrosion resistance, blending theoretical insights and practical applications to enhance our grasp of corrosion prevention mechanisms and establish a systematic approach to coating design. The groundbreaking significance of this study lies in its innovative integration of the TA/pH concept, which encompasses the TA/pH… More >

Fatemeh Hassani Khorshidi¹, Saeed Kazemi Najafi¹, Farhood Najafi^2,*, Antonio Pizzi^3,*, Dick Sandberg⁴, Rabi Behrooz¹

Journal of Renewable Materials, Vol.12, No.2, pp. 305-323, 2024, DOI:10.32604/jrm.2023.043953 - 11 March 2024

Abstract The purpose of this research study was to investigate the properties of polyurethane coatings based on lignin nano-particles. For this purpose, the prepared coatings were applied to pine wood surfaces and weathered artificially. Subsequently, color and gloss of the coatings were measured before and after the weathering test. Field emission scanning electron microscopy (FE-SEM) micrographs prepared from the coatings showed that the average size of nano-particles in the polyurethane substrate was approximately 500 nm. Nuclear magnetic resonance (¹³C-NMR) spectroscopy showed that strong urethane bonds were formed in the nano-lignin-based polyurethane. Differential calorimetric analysis (DSC) test revealed… More > Graphic Abstract

Lianyuan Ji¹, Mingchen Shi¹, Zengkai Feng², Hui Yang^1,*

Journal of Renewable Materials, Vol.12, No.2, pp. 259-274, 2024, DOI:10.32604/jrm.2023.030599 - 11 March 2024

Abstract

Cobalt sulphides attract much attention as anode materials for Li-ion batteries (LIBs). However, its poor conductivity, low initial column efficiency and large volume changes during cycling have hindered its further development. Herein, novel interlaced CoS nanosheets were firstly prepared on Carbon Fiber Cloth (CFC) by two hydrothermal reactions followed with carbon coating via carbonizing dopamine (CoS NS@C/CFC). As a freestanding anode, the nanosheet structure of CoS not only accommodates the volume variation, but also provides a large interface area to proceed the charge transfer reaction. In addition, CFC works as both a three-dimensional skeleton and an

… More >

Wei Shi^1,2, Zhengyi Li¹, Xiaobing Xu¹, Yingshui Yu¹, Xiaofei Ding¹, Heng Ju^1,*

FDMP-Fluid Dynamics & Materials Processing, Vol.20, No.1, pp. 97-108, 2024, DOI:10.32604/fdmp.2023.029028 - 08 November 2023

Abstract Two-dimensional carbon/carbon (2D C/C) composites are a special class of carbon/carbon composites, generally obtained by combining resin-impregnated carbon fiber clothes, which are then cured and carbonized. This study deals with the preparation of a protective coating for these materials. This coating, based on graphite, was prepared by the slurry method. The effect of graphite and phenolic resin powders with different weight ratios was examined. The results have shown that the coating slurry can fill the pores and cracks of the composite surface, thereby densifying the surface layer of the material. With the increase of the… More >

LIJUN CHEN^*, ZHEQING GONG, ZHENGRONG FU

Journal of Polymer Materials, Vol.40, No.3-4, pp. 157-164, 2023, DOI:10.32381/JPM.2023.40.3-4.3

Abstract The organic fluorine modified/containing cationic acrylic resin is prepared via solution polymerization technique using hexafluorobutyl methacrylate (HFMA) along with butyl acrylate (BA), methyl methacrylate (MMA), styrene (St), dimethylaminoethyl methacrylate (DMAEMA) and hydroxy propyl methacrylate (HPMA) as the comonomers, proprylene glycol monomethyl ether (PGME) as the solvent, and 2, 2-Azo-bis-iso-butyronitrile (AIBN) as the initiator. The synthesized resin in which fluorine atom is introduced into the polymer chains. The cathodic electrodeposition (CED) coatings were prepared by mixing the synthesized resin and blocked isocyanate. The influence of the amount of organic fluorine on the resin and the resultant More >

Bengang Zhang^1,*, Antonio Pizzi^2,*, Mathieu Petrissans¹, Anelie Petrissans¹, Colin Baptiste¹

Journal of Renewable Materials, Vol.11, No.12, pp. 4097-4121, 2023, DOI:10.32604/jrm.2023.029761 - 10 November 2023

Abstract Aminated tannins were prepared by reacting mimosa condensed tannin extract with ammonia yielding the substitution of many, if not all of the tannin hydroxyl groups with –NH₂ groups. A tannin-aminated tannin (ATT) particleboard coating was then prepared by reacting raw tannin extract with aminated tannin extract and thus cross-liking the two by substituting tannin’s hydroxyl groups with the –NH₂ groups on the aminated tannin to form –NH-bridges between the two. The resulting particleboard coating gave encouraging results when pressed at 180°C for 3 min. Conversely, the system in which tannin was reacted/cross-liked with urea (ATU) by… More >

Demiao Chu¹, Redžo Hasanagić², Leila Fathi³, Mohsen Bahmani^3,*, Miha Humar⁴

Journal of Renewable Materials, Vol.11, No.12, pp. 4061-4078, 2023, DOI:10.32604/jrm.2023.043657 - 10 November 2023

Abstract This study aimed to investigate the water absorption capacity of thermally modified and non-modified spruce and blue-stained spruce wood. The wettability of wood depends on various factors, including its type, density, porosity, and surface treatment. Wood can swell and become distorted when exposed to water or humidity, impacting its structural integrity. Hence, it is crucial to consider the water and water vapour uptake in the wood when choosing materials for applications that are likely to be exposed to moisture. Various moisture absorption tests were conducted to assess water absorption capacity, including short-term and long-term water… More > Graphic Abstract

Pan Li¹, Xiaochao Jin¹, Pin Lv¹, Xueling Fan^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.26, No.1, pp. 1-1, 2023, DOI:10.32604/icces.2023.010540

Abstract Refurbishment of thermal barrier coating (TBC) has become a valuable technique to prolong the service life of high-temperature components. In this work, the effect of refurbishment process on the oxidation behaviors of TBC was investigated. Before recoating, the soft chemical stripping method was used to remove TBC from DD6 single-crystal superalloy. The results showed that a certain amount of IDZ layer with Cr-rich would be retained in the DD6 superalloy substrate after coating removal. The characteristics of the β phases change from the elongated grain shapes and a high aspect ratio in the ordinary specimens… More >

Liuyu Yang¹, Peng Jiang¹, Tiejun Wang^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.3, pp. 1-1, 2023, DOI:10.32604/icces.2023.010538

Abstract Air Plasma Sprayed (APS) Thermal Barrier Coatings (TBCs) have been widely used in land-based gas engines for enhancing the high temperature performance due to their outstanding thermal insulation and high durability. Introducing the segment cracks into APS-TBCs to enhance its durability has been quite attractive approaches nowadays. Qualitative conclusions have been drawn to explore the mechanisms on segment crack formation in the past decades. This article acts as a quantitative study of segment crack formation and crack density regulation mechanism in APS Yttria-Stabilized Zirconia (YSZ) TBCs with experimental observations and analytical calculations. An in-situ stress… More >

Biao Li^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.1, pp. 1-2, 2023, DOI:10.32604/icces.2023.09818

Abstract High-temperature coatings are extensively used in aircraft engines and industrial gas turbines to protect hot-section components from harsh operating environments [1]. Representative high-temperature coatings include thermal barrier coatings and environmental barrier coatings, which are applied to substrates made of superalloy and ceramic matrix composites, respectively. The durability of the coatings is of significant importance for the structural integrity of the components [2-4]. A segmented microstructure was widely used to improve the coatings' durability. A network of through-thickness vertical cracks is introduced into the outer layer of the coatings, which increases the compliance of the coatings… More >