Rui Lu¹, Zhanjun Wu¹, Qi Zhou¹, Hao Xu^1,*

Structural Durability & Health Monitoring, Vol.13, No.3, pp. 267-287, 2019, DOI:10.32604/sdhm.2019.06323

Abstract Structural health monitoring (SHM) is a research focus involving a large category of techniques performing in-situ identification of structural damage, stress, external loads, vibration signatures, etc. Among various SHM techniques, those able to monitoring structural deformed shapes are considered as an important category. A novel method of deformed shape reconstruction for thin-walled beam structures was recently proposed by Xu et al. [1], which is capable of decoupling complex beam deformations subject to the combination of different loading cases, including tension/compression, bending and warping torsion, and also able to reconstruct the full-field displacement distributions. However, this method was demonstrated only under… More >

Le Van Hai^1,2, Lindong Zhai¹, Hyun Chan Kim¹, Jung Woong Kim¹, Jaehwan Kim^1,*

Journal of Renewable Materials, Vol.7, No.7, pp. 621-629, 2019, DOI:10.32604/jrm.2019.06466

Abstract This paper reports green nanocomposites made by blending polyvinyl alcohol (PVA) with cellulose nanofiber (CNF) isolated from recycled deinked copy/printing paper (DIP). The reinforcement effect of DIPCNF in the nanocomposites is compared with other CNFs isolated from native cotton and hardwood by means of TEMPO-oxidation. The prepared PVA-CNF nanocomposites are characterized in terms of morphology, chemical interaction, structural, thermal and mechanical properties. X-ray diffraction and Fourier transform infrared spectroscopy confirm the reinforcing ability of cellulose nanofibers into PVA. By blending CNFs into PVA matrix, the thermal stability of the nanocomposites is improved and DIPCNF shows similar enhancement effect with COCNF… More >

B. Benobeidallah¹, A. Benhamida¹, A. Dorigato^2,*, A. Sola³, M. Messori³, A. Pegoretti²

Journal of Renewable Materials, Vol.7, No.1, pp. 89-102, 2019, DOI:10.32604/jrm.2019.00136

Abstract Various amounts (up to 10 wt%) of palygorskite nanofibers functionalized by 3-aminopropyltriethoxysilane (APTES) coupling agent were used to reinforce polyamide 11 nanocomposites prepared by melt compounding. The covalent bonding of the silane on the palygorskite surface was confirmed by infrared spectroscopy and thermogravimetric analysis. X-ray diffraction revealed the retention of the α-form of polyamide crystals upon the addition of both natural and silane treated palygorskite nanorods. All the investigated nanocomposites showed an improvement of the thermal stability, especially when surface treated palygorskite nanofibers were considered. Tensile tests and dynamic mechanical thermal analyses on the prepared materials evidenced how the incorporation… More >

Marcin Masłowski*, Justyna Miedzianowska and Krzysztof Strzelec

Journal of Renewable Materials, Vol.6, No.7, pp. 746-754, 2018, DOI:10.32604/JRM.2018.00121

Abstract Novel elastomer biocomposites based on straw fibers (raw or chemically modified) as reinforcing elements of natural rubber (NR) were reported and studied. Oat straw fibres with different average lengths were used. Lignocellulose materials were incorporated into the elastomer, before and after chemical surface modification involving sodium hydroxide. Fourier transform infrared spectroscopy (FTIR) and microscopy techniques were employed for characterization of fillers. The kinetics of rubber mixtures, as well as rheometric properties of compounds were determined. The cross-linking density was executed on the basis of equilibrium solvent-swelling measurements applying the modified Flory–Rehner equation. The morphology of biocomposites samples was analyzed by… More >

Hynek Beneš, Aleksandra Paruzel*, Jiří Hodan and Olga Trhlíková

Journal of Renewable Materials, Vol.6, No.7, pp. 697-706, 2018, DOI:10.32604/JRM.2018.00011

Abstract In this study, castor oil, rapeseed oil and medium chain triglycerides of coconut oil, were transesterified by means of 2-ethyl-2-hydroxymethyl-1,3-propanediol (trimethylolpropane) and consequently used to convert polycarbonate waste from end-of-life vehicles into liquid polyols. The prepared recycled polyols, composed uniquely of renewable and recycled components, had a hydroxyl number of ca. 250 mg KOH·g−1. They were successfully applied as 100% replacement of a virgin polyol for preparation of solid crosslinked polyurethanes (PU) by solvent-free casting. The produced rigid cast PU exhibited the main transition temperature ranging from 44°C to 53°C, the hardness value from 46 to 61 Shore D and… More >

S. Gaidukovs^1,2,*, G. Gaidukova², A. Ivdre^1,3, U. Cabulis³

Journal of Renewable Materials, Vol.6, No.7, pp. 755-763, 2018, DOI:10.7569/JRM.2018.634112

Abstract This article deals with the study of the viscoelastic and thermal properties of polyurethane (PU) rigid foams from biobased and recycled components. Rapeseed oil (RO) and recycled poly(ethylene terephthalate) (PET) were used to synthesize PU polyols. Addition of adipic acid (ADA) to polyol resulted in improved thermal and viscoelastic properties of foam materials. ADA content was varied from 1 to 6 wt%. Results of the dynamic mechanical spectra indicate an increase of the storage modulus E′ and the loss modulus E″ in the whole temperature range for specimens with higher loading of ADA. In addition, damping factor shifted to higher… More >

Ewa Majchrzak^{2 1}, Marek Paruch²

The International Conference on Computational & Experimental Engineering and Sciences, Vol.1, No.1, pp. 7-14, 2007, DOI:10.3970/icces.2007.001.007

Abstract This article has no abstract. More >

Shy-Pin Cuo¹, Dein Shaw²

The International Conference on Computational & Experimental Engineering and Sciences, Vol.9, No.3, pp. 199-200, 2009, DOI:10.3970/icces.2009.009.199

Abstract The purpose of this study is to present the process of development of HID (High Intensity Discharge) light reflector of a streetlight. The new application of HID light source for streetlight product is proposed in this study, the advantages of HID include low power consumption and single point light source emitting. The study includes the introduction of HID streetlight structure, the lighting efficiency comparison of various light sources (ex. High Pressure Sodium-lamp ``HPS'', High Bright LED ``HB LED'', etc\ldots ), and the design of streetlight reflector. The emphases of the experiment are focused at light reflector design; the streetlight module… More >

Prasert Prapamonthon^1,2,*, Soemsak Yooyen¹, Suwin Sleesongsom¹

CMES-Computer Modeling in Engineering & Sciences, Vol.119, No.3, pp. 593-615, 2019, DOI:10.32604/cmes.2019.05579

Abstract Thermal parameters are important variables that have great influence on life time of turbine vanes. Therefore, accurate prediction of the thermal parameters is essential. In this study, a numerical approach for conjugate heat transfer (CHT) and computational fluid dynamics (CFD) is used to investigate thermal sensitivity of a transonic guide vane which is fully film-cooled by 199 film holes. Thermal barrier coating (TBC), i.e., the typical TBC and a new one as the candidate TBC, and turbulence intensity (Tu), i.e., Tu=3.3%, 10% and 20%, are two variables used for the present study. At first the external surface temperatures of the… More >

Jin Yeon Cho¹, Jae Mo An², You Me Song¹, Seungsoo Lee¹, Dong Whan Choi¹

CMES-Computer Modeling in Engineering & Sciences, Vol.9, No.1, pp. 1-18, 2005, DOI:10.3970/cmes.2005.009.001

Abstract A displacement welding technique is proposed to carry out coupled analysis of the integrated whole model which consists of independently modeled finite element substructures. In the proposed method, the incompatible displacement fields in the interfaces of independently modeled substructures are directly welded together through a blended function that is newly defined in the transient region of mismatching interface. To construct the blended function, the moving least squares function, which does not require well-defined nodal connectivity, is utilized along with the original finite element shape function. The meshless character of the moving least squares function makes it possible to efficiently handle… More >