T. Fu, C.P. Wang, B. Hou, X.D. Zhu, Z.F. Zhou, K.Y. Li, J. Lu

The International Conference on Computational & Experimental Engineering and Sciences, Vol.20, No.3, pp. 91-92, 2011, DOI:10.3970/icces.2011.020.091

Abstract Structural steels are widely used in engineering fields. Generally, they have the advantage of lower prices due to less precious alloy elements contained; however, their properties, especially the surface properties are inferior to high alloy steels. Surface engineering are of importance in improving surface properties of steels, and even a 'new' surface layer with high performances can be produced by surface technologies on low cost structural steels with ordinary properties.
The researches of last decade have shown that surface nanocrystallization (SNC) can markedly improve surface mechanical properties of metallic materials and accelerate thermal diffusion of N, Cr, etc atoms. In… More >

Qin Siwei, Shen SP

The International Conference on Computational & Experimental Engineering and Sciences, Vol.19, No.2, pp. 53-54, 2011, DOI:10.3970/icces.2011.019.053

Abstract Among many multiscale methods ,we choose the quasicontinuum method to understand the mechanical response at the nanocrystalline of grain boundaries(GBs) under tension. The energetic and mechanical strength of 6 i?"<110> symmetric tilt GBs are investigated in nanocrystalline Cu and Ni. We focus on discussing the interaction of the structural units of symmetric tilt GB for the initial deformation mode and the strength of model. At the basis of the previous, We study the nanocrystalline Cu/a-Al2O3 interface and analyze the relationship during the grains orientations, GB energy and interface. Special emphasis is placed on the crystal slip from the interface across… More >

Abeer M. Adel¹, Amira M. El-Shafei², Atef A. Ibrahim¹, Mona T. Al-Shemy^1,*

Journal of Renewable Materials, Vol.7, No.6, pp. 567-582, 2019, DOI:10.32604/jrm.2019.00034

Abstract In this study, nanocrystalline celluloses were used to enhance physical, mechanical and water vapor barrier properties of chitosan films for potential food packaging applications. Two different mineral acids (sulfuric and phosphoric) were used to extract nanocrystalline cellulose from date palm sheath fibers. The influence of cellulose I and cellulose II on the properties of the isolated nanocrystalline celluloses (e.g., yield, energy and length of intra- and intermolecular hydrogen bonds, and degree of substitution) were studied too. The characteristics of chitosan biocomposite film with phosphorylated nanocrystalline cellulose were compared to those with sulfated nanocrystalline cellulose. Results showed that besides cellulose polymorphism,… More >

Marcia Cristina Branciforti^1,*, Caroline Faria Bellani², Carolina Lipparelli Morelli², Alice Ferrand³, Nadia Benkirane-Jessel³, Rosario Elida Suman Bretas²

Journal of Renewable Materials, Vol.7, No.3, pp. 269-277, 2019, DOI:10.32604/jrm.2019.01833

Abstract Although nanocomposites have recently attracted special interest in the tissue engineering area, due to their potential to reinforce scaffolds for hard tissues applications, a number of variables must be set prior to any clinical application. This manuscript addresses the evaluation of thermo-mechanical properties and of cell proliferation of cellulose nanocrystals (CNC), poly(butylene adipate-co-terephthalate) (PBAT), poly(ε-caprolactone) (PCL) films and their bionanocomposites with 2 wt% of CNC obtained by casting technique. Cellulose nanocrystals extracted from Balsa wood by acid hydrolysis were used as a reinforcing phase in PBAT and PCL matrix films. The films and pure CNC at different concentrations were cultured… More >

Ingrid Souza Vieira da Silva¹, Natália Soares Prado¹, Patrícia Gontijo de Melo², Danilo Campion Arantes³, Mara Zeni Andrade⁴, Harumi Otaguro¹, Daniel Pasquini^1,*

Journal of Renewable Materials, Vol.7, No.1, pp. 73-87, 2019, DOI:10.32604/jrm.2019.00042

Abstract In this work, nine different types of edible coating based on pectin, cellulose nanocrystals, glycerol, and essential oil of lemongrass were prepared and used to coat strawberries with a film formed directly on the surface of the coated fruit. The effects of the different edible coatings on refrigerated fruits in terms of weight loss, titratable acidity, total soluble solids, pH, and anthocyanin content was evaluated after 2 days, 4 days, 6 days, and 8 days of storage. Application of the edible coatings reduced the weight loss of the coated strawberries and the anthocyanin content. The total soluble solids content of… More >

Ragab E. Abou-Zeid^1*, Mohamed A. Diab¹, Salah A. A. Mohamed², Ahmed Salama¹, Hind Abdullah Aljohani³, Kamel Rizq Shoueir⁴

Journal of Renewable Materials, Vol.6, No.4, pp. 394-401, 2018, DOI:10.7569/JRM.2017.634156

Abstract The current article addresses a new strategy for the preparation of polylactic acid/cellulose nanocrystal (PLA/CNCs) nanobiocomposite films with improved structural morphology, mechanical and barrier properties for food packaging applications. The addition of hexadecyltrimethylammonium bromide (CTAB) and sodium lauryl sulfate (SLS) as cationic and anionic surfactants respectively, was found to play a crucial role in preventing re-aggregation of the CNCs during drying and improving the dispersion of CNCs in the PLA. The coated paper was characterized using mechanical tests, water vapor permeability (WVP), X-ray diffraction (XRD), scanning electron microscopy (SEM) and air permeability. The results showed that the paper coated with… More >

Christophe Olivier^1,2, Jean Bruno Mougel^1,2, Patricia Bertoncini¹, Celine Moreau², Isabelle Capron², Bernard Cathala², Olivier Chauvet^1*

Journal of Renewable Materials, Vol.6, No.3, pp. 237-241, 2018, DOI:10.7569/JRM.2017.634168

Abstract Cellulose nanocrystals (CNCs) have a high ability to disperse single-walled carbon nanotubes (SWNTs) in aqueous media and to form hybrids. These hybrids are used to grow layer-by-layer thin films of controlled thickness. Thanks to the presence of SWNTs, these films are conducting. In this article, we describe the process by which the CNC/SWNT hybrids are obtained and discuss the electrical properties of the hybrid-based layer-by-layer films. More >

Weijun Yang^1†, Xiaomin Zhao^2†, Elena Fortunati¹, Franco Dominici¹, Jose M. Kenny¹, Debora Puglia^1*, De-Yi Wang^2*

Journal of Renewable Materials, Vol.5, No.5, pp. 423-434, 2017, DOI:10.7569/JRM.2017.634146

Abstract Presented herein is a deep investigation of the fire, mechanical and thermal performances of poly(lactic acid) (PLA)-based nanocomposites, which were obtained by combining cellulose nanocrystals (CNC) with various contents of N,N’-diallyl-phenylphosphoricdiamide (P-AA) via a two-steps masterbatch melt extrusion process (glycidyl methacrylate grafting on PLA and CNC premixing with PLA). Results have shown that the value of the limiting oxygen index (LOI) increased to 28.8% and a V-0 rating in UL94 test was obtained when 2 wt% of P-AA was added in the presence of cellulose nanocrystals (3 wt%). The incorporation of CNC induced a decrease of both PHRR and THR… More >

Melissa Camacho¹, Yendry Regina Corrales Ureña^*,1, Mary Lopretti², Leonel Bustamante Carballo¹, Galia Moreno¹, Brian Alfaro¹, Jose Roberto Vega Baudrit^1,3

Journal of Renewable Materials, Vol.5, No.5, pp. 271-279, 2017, DOI:10.7569/JRM.2017.634117

Abstract Pineapple peel biomass was used as raw material for nanocellulose extraction. The raw material is a residue from the Costa Rican fruit industry. The nanocellulose was obtained by a two-step hydrolysis process. Firstly, the cellulose was hydrolyzed with HCl to obtain microcrystalline cellulose. In the second step, the hydrolysis was carried out using H2SO4 to obtain smaller fragments and decrease the lignin content. A timedependent study was carried out to determine the particle size decrease depending on the contact time with the H2SO4. The chemical, thermal and morphological properties were analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA),… More >

F. Luzi¹, E. Fortunati^1*, A. Jiménez², D. Puglia¹, A. Chiralt², L. Torre¹

Journal of Renewable Materials, Vol.5, No.2, pp. 103-115, 2017, DOI:10.7569/JRM.2016.634135

Abstract Poly(lactic acid) (PLA) based nanocomposites reinforced with 1 wt% of surfactant-modified cellulose nanocrystals (s-CNC) extracted from Posidonia oceanica plant waste and zinc oxide nanoparticles (ZnO NPs) at different concentrations (0.1 and 0.5 wt%) were prepared by solvent casting process. Their thermal, morphological, optical, mechanical and water vapor permeability properties were investigated. Tensile testing showed increased values for strength and deformation at break in PLA based formulations reinforced with s-CNC and ZnO NPs as a consequence of better nanofiller dispersion compared to binary films reinforced only with ZnO NPs. Moreover, the effect of s-CNC and ZnO NPs provoked an improvement of… More >