F. J. Santiago-Medina¹, A. Pizzi^{1, 2*}, M. C. Basso¹, L. Delmotte³, S. Abdalla²

Journal of Renewable Materials, Vol.5, No.5, pp. 388-399, 2017, DOI:10.7569/JRM.2017.634142

Abstract The reaction of a desulphurized kraft lignin with hexamethylene diamine as a model of a polyamine has been investigated. For this purpose, guaiacol was also used as a lignin model compound and treated under similar conditions. Solid state CP-MAS 13C NMR, FTIR and MALDI-TOF spectroscopy studies revealed that polycondensation compounds leading to resins were obtained by the reaction of the amines with the phenolic and aliphatic hydroxy groups of lignin. Simultaneously a second reaction leading to the formation of ionic bonds between the same groups occurred. These new reactions have been clearly shown to involve several phenolic and alcohol hydroxyl… More >

N. A. Sri Aprilia¹, M. S. Nurul Atiqah², Zhari Ismail³, C. Y. Loo², Chaturbhuj K. Saurabh², Rudi Dungani⁴, Abdul Khalil H.P.S^2*

Journal of Renewable Materials, Vol.5, No.5, pp. 380-387, 2017, DOI:10.7569/JRM.2017.634130

Abstract Due to environmental concerns, green composites have become a highly researched material. In the present study, kenaf fiber was used as reinforcement in epoxy-based composite with weight fraction ranges from 0, 5, 10, and 15% (w/w of resin). The ratio of epoxy to hardener was 65:32.5. Prior to incorporation, kenaf bast fiber underwent Soda-AQ pulping followed by total chlorine-free bleaching (OAZP sequence). The obtained pulp was then subjected to supercritical carbon dioxide extraction (SCE) treatment. It was observed that epoxy composite with 10% of fiber loading demonstrated the highest mechanical properties with a tensile strength of 64 MPa, tensile modulus… More >

Arun Kumar Pradhan^1,2*, Prafulla Kumar Sahoo¹, Pradeep Kumar Rana²

Journal of Renewable Materials, Vol.5, No.5, pp. 371-379, 2017, DOI:10.7569/JRM.2017.634129

Abstract Chitosan grafted with poly(methyl-methacrylate) (PMMA) and adsorbed with kaolin functionalized as bioadhesive was prepared via emulsion polymerization technique and physiochemically characterized as a bone-graft substitute. The so prepared grafted bioactive bone cement (BBC) bionanocomposites (BNCs), chitosan-g-PMMA/kaolin, was characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) analysis, field-emission scanning electron microscopy (FESEM) and thermogravimetric analysis (TGA). The water uptake, retention ability and the nanosize particle arrangement in the polymeric BBC-BNCs were studied along with the mechanical and biodegradation properties. These preliminary investigations of the BNCs will open the door for their use in bioadhesive bone-cement implants in the future. More >

M. Purushothaman^†,1, P. Santhana Gopala Krishnan^1,2*, S. K. Nayak^1,2

Journal of Renewable Materials, Vol.5, No.5, pp. 363-370, 2017, DOI:10.7569/JRM.2017.634128

Abstract In the present work, the hydrophilicity and thermal behavior of nanocomposites of poly(butyl lactate methacrylate) were investigated using different weight percent of sepiolite. These nanocomposites were prepared by solution casting method. X-ray diffraction (XRD) studies indicated that the increase in sepiolite content decreased the average molecular interchain spacing () values from 7.18 to 6.23 Å in nanocomposites. Apart from the amorphous halo peak of nanocomposites, the appearance of crystalline peak at 7.41° was due to the d110 plane of sepiolite. Surface morphology of nanocomposites was studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques and the uniform… More >

E. M. Ciannamea, D. C. Marin, R. A. Ruseckaite, P. M. Stefani^*

Journal of Renewable Materials, Vol.5, No.5, pp. 357-362, 2017, DOI:10.7569/JRM.2017.634125

Abstract In the development of materials based on renewable resources, the search for lignocellulosic substitutes for wood is one of the biggest challenges that academia and the particleboard and wood industries are facing. In this article, particleboards were processed using rice husk, an agricultural waste, as a substitute for wood. Rice husk without any further treatment was processed into particleboards using phenol-formaldehyde resin as binder. The effect of the processing parameters, pressure and binder content (BC) on the density, water absorption (WA), thickness swelling (TS), modulus of rupture (MOR) and modulus of elasticity (MOE) was analyzed. The performance of the obtained… More >

G. Mondragon, C. Peña-Rodriguez, A. Eceiza, A. Arbelaiz^*

Journal of Renewable Materials, Vol.5, No.5, pp. 345-356, 2017, DOI:10.7569/JRM.2017.634124

Abstract In this work, the main chemical reactions conditions of a succession of specific chemical treatments used for the isolation of nanocellulose from sisal fibers were evaluated. The novelty of this work is the study done to analyze the effect of different reaction conditions (time or concentration) in fiber structure and composition as well as in the characteristics of obtained cellulosic samples. In order to achieve this goal different physicochemical, thermal and morphological characterization techniques were used after each chemical treatment and the most suitable reaction conditions were selected for the subsequent treatment. Moreover, the thermal stability evolution of cellulose nanocrystals… More >

Shegufta Shetranjiwalla, Shaojun Li, Laziz Bouzidi, Suresh S. Narine^*

Journal of Renewable Materials, Vol.5, No.5, pp. 333-344, 2017, DOI:10.7569/JRM.2017.634102

Abstract The impact of polymerization protocol on phase structure and properties of entirely lipid-derived thermoplastic poly(ester urethane)s (TPEU)s was investigated. The TPEUs were synthesized from 1,7-heptamethylene diisocyanate, polyester diols and 1,9-nonanediol (ND) as chain extender. A two-stage polymerization method was used to prepare two TPEUs; one in which ND was added in the first stage of polymerization as part of the prepolymer and another in the second stage after the prepolymer was formed. Two very different morphologies exhibiting different degrees of phase separation were obtained, driven by the sequence of addition of the chain extender. The incorporation of the chain extender… More >

Melissa Camacho¹, Yendry Regina Corrales Ureña^*,1, Mary Lopretti², Leonel Bustamante Carballo¹, Galia Moreno¹, Brian Alfaro¹, Jose Roberto Vega Baudrit^1,3

Journal of Renewable Materials, Vol.5, No.5, pp. 271-279, 2017, DOI:10.7569/JRM.2017.634117

Abstract Pineapple peel biomass was used as raw material for nanocellulose extraction. The raw material is a residue from the Costa Rican fruit industry. The nanocellulose was obtained by a two-step hydrolysis process. Firstly, the cellulose was hydrolyzed with HCl to obtain microcrystalline cellulose. In the second step, the hydrolysis was carried out using H2SO4 to obtain smaller fragments and decrease the lignin content. A timedependent study was carried out to determine the particle size decrease depending on the contact time with the H2SO4. The chemical, thermal and morphological properties were analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA),… More >

Enzo Alvarado-Cordero¹, Gabriela Montes de Oca-Vásquez², Reinaldo Pereira-Reyes², José Vega-Baudrit², Marianelly Esquivel-Alfaro^1*

Journal of Renewable Materials, Vol.5, No.3-4, pp. 323-331, 2017, DOI:10.7569/JRM.2017.634123

Abstract Biodegradable polymers from renewable resources are generating growing interest in the plastic industry because they have properties similar to synthetic polymers. Polyhydroxyalkanoates, mainly polyhydroxybutyrate (PHB), have mechanical and physicochemical properties very similar to their synthetic counterparts. This work explores the use of residual glycerol from the bioenergy industry for the production of PHB by Bacillus megaterium DSM 32. The glycerol works as a source of carbon and energy. Raw glycerol was purified with sulfuric acid in order to neutralize saponified fatty acids. The purification process generated three different phases. One of the phases was the glycerol-rich layer; this layer was… More >

Nicole Segura Salas¹, Felipe Orozco Gutiérrez³, Luis Daniel Mora Murillo², Yendry Corrales Ureña³, Shakira Johnson¹, José Vega Baudrit³, Rodolfo Jesús González-Paz^3*

Journal of Renewable Materials, Vol.5, No.3-4, pp. 313-322, 2017, DOI:10.7569/JRM.2017.634122

Abstract Vegetable oils are being used for the production of biodegradable polymers, opening new possibilities for the synthesis of greener materials that could compete in national markets with petroleum-based polymers. In this study, castor oil and a catalyst (cobalt[II] naphtenate as promotor and MEKP as initiator) from local stores and styrene in different ratios were used to produce thermostable polymers. The kinetics of the polymerization reaction was followed by infrared spectroscopy. A polymeric material was synthetized which presents good mechanical properties. Therefore, composites were produced using 1 wt% of microcellulose extracted from biomass waste as reinforcement or 1 wt% microsilica to… More >