Surkay D. Akbarov^1,2, Resat Kosker³, Nihan T. Cinar³

CMC-Computers, Materials & Continua, Vol.21, No.2, pp. 119-146, 2011, DOI:10.3970/cmc.2011.021.119

Abstract In the present paper, the stress distribution in an infinite elastic body containing two neighboring nanofibers is studied. It is assumed that the midlines of the fibers are in the same plane. With respect to the location of the fibers according to each other the co-phase and anti-phase curving cases are considered. At infinity uniformly distributed normal forces act in the direction of the nanofibers, location. The investigations are carried out in the framework of the piecewise homogeneous body model with the use of the three-dimensional geometrically non-linear exact equations of the theory of elasticity. The normal and shear self-equilibrated… More >

G. Gang¹, Y.H. Liu²

CMC-Computers, Materials & Continua, Vol.20, No.3, pp. 251-272, 2010, DOI:10.3970/cmc.2010.020.251

Abstract Limit and shakedown analysis theorems are the theories of classical plasticity for the direct computation of the load-carrying capacity under proportional and varying loads. Based on Melan's theorem, a solution procedure for lower bound limit and shakedown analysis of three-dimensional (3D) structures is established making use of the finite element method (FEM). The self-equilibrium stress fields are expressed by linear combination of several basic self-equilibrium stress fields with parameters to be determined. These basic self-equilibrium stress fields are elastic responses of the body to imposed permanent strains obtained through elastic-plastic incremental analysis by the three-dimensional finite element method (3D-FEM). The… More >

X. H. Du¹, X. P. Shen¹

CMC-Computers, Materials & Continua, Vol.20, No.3, pp. 225-242, 2010, DOI:10.3970/cmc.2010.020.225

Abstract Aim of this paper is to estimate the integrity of liquefied natural gas (LNG) prestressed storage tank under seismic influence. The coupled Eulerian-Lagrangian (CEL) analysis technique is used to simulate the fluid-structure interaction between LNG and the cylinder of LNG prestressed storage tank. The 3-D model of LNG has been dispersed by Eulerian mesh that is different from traditional analysis method which is called the added mass method. Meanwhile, both of the 3-D models of prestressed rebar and concrete structure are dispersed by Lagrangian mesh. Following conclusions are obtained: 1) Natural frequency of the whole model has been obtained by… More >

N.J. Bartle¹, P.D. Gosling¹

CMC-Computers, Materials & Continua, Vol.20, No.1, pp. 19-62, 2010, DOI:10.3970/cmc.2010.020.019

Abstract ETFE cushions are increasingly being used to form high-profile facades and structural forms. This investigation aims to extend an analytical theory of large deformation in order to predict the shape and stress distributions of an un-patterned square ETFE cushion without the need to resort to discretised numerical methods. In order to assess the validity of the theoretical procedure a prototype cushion has been analysed using a finite element simulation. The theoretical procedure is also compared with alternative approximate equations proposed for the design of ETFE cushions. More >

A. Rama Ch,ra Murthy^1,2, G.S. Palani¹, Nagesh R. Iyer^1,3, M Srinivasa Pavan¹, Smitha Gopinath¹

CMC-Computers, Materials & Continua, Vol.19, No.2, pp. 135-154, 2010, DOI:10.3970/cmc.2010.019.135

Abstract This paper presents methodologies for fracture analysis of concrete structural components with and without considering tension softening effect. Stress intensity factor (SIF) is computed by using analytical approach and finite element analysis. In the analytical approach, SIF accounting for tension softening effect has been obtained as the difference of SIF obtained using linear elastic fracture mechanics (LEFM) principles and SIF due to closing pressure. Superposition principle has been used by accounting for non-linearity in incremental form. SIF due to crack closing force applied on the effective crack face inside the process zone has been computed using Green's function approach. In… More >

L.L. Zhu^1,2,3, X.J. Zheng^1,2

CMC-Computers, Materials & Continua, Vol.18, No.3, pp. 301-320, 2010, DOI:10.3970/cmc.2010.018.301

Abstract The phonon properties of spatially confined nanofilms under the preexisting stress fields are investigated theoretically by accounting for the confinement effects and acoustoelastic effects. Due to the spatial confinement in low-dimensional structures, the phonon dispersion relations, phonon group velocities as well as the phonon density of states are of significant difference with the ones in bulk structures. Here, the continuum elasticity theory is made use of to determine the phonon dispersion relations of shear modes (SH), dilatational modes (SA) and the flexural modes (AS), thus to analyze the contribution of stress fields on the phonon performance of confined nanofilms. Our… More >

Surkay D. Akbarov^1,2, Resat Kosker³, Yasemen Ucan³

CMC-Computers, Materials & Continua, Vol.17, No.2, pp. 77-102, 2010, DOI:10.3970/cmc.2010.017.077

Abstract In the framework of the piecewise homogeneous body model with the use of the three-dimensional geometrically non-linear exact equations of the theory of elasticity, the method for determination of the stress-strain state in the infinite body containing periodically located row of periodically curved fibers is developed. It is assumed that the midlines of the fibers are in the same plane. With respect to the location of the fibers according to each other the sinphase and antiphase curving cases are considered. Numerical results on the effect of the geometrical non-linearity to the values of the self balanced shear and normal stresses… More >

Zone-Ching Lin¹and Ren-Yuan Wang¹

CMC-Computers, Materials & Continua, Vol.16, No.3, pp. 247-272, 2010, DOI:10.3970/cmc.2010.016.247

Abstract The paper establishes a new three-dimensional quasi-steady molecular statics nanoscale abrasive cutting model to investigate the abrasive cutting behavior in the downpressing and abrasive cutting process of a workpiece in chemical mechanical polishing (CMP) process. The downpressing and abrasive cutting process is a continuous process. The abrasive cutting process is done after the single abrasive particle has downpressed and penetrated a workpiece to a certain depth of a workpiece. The paper analyzes the effects of the abrasive particles with different diameters on action force. It also analyzes the action force change of abrasive particles with different diameters on the projected… More >

Xue-Qian Fang^1,2, Xiao-Hua Wang¹, Le-Le Zhang³

CMC-Computers, Materials & Continua, Vol.16, No.3, pp. 229-246, 2010, DOI:10.3970/cmc.2010.016.229

Abstract In the design of advanced micro- and nanosized materials and devices containing inclusions, the effects of surfaces/interfaces on the stress concentration become prominent. In this paper, based on the surface/interface elasticity theory, a two-dimensional problem of an elliptical nano-inhomogeneity under anti-plane shear waves is considered. The conformal mapping method is then applied to solve the formulated boundary value problem. The analytical solutions of displacement fields are expressed by employing wave function expansion method, the expanded mode coefficients are determined by satisfying the boundary conditions at the interfaces of the nano-inhomogeneity. Analyses show that the effect of the interfacial properties on… More >

M.R. Khoshravan¹ and M.A. Setoodeh¹

CMC-Computers, Materials & Continua, Vol.16, No.3, pp. 195-228, 2010, DOI:10.3970/cmc.2010.016.195

Abstract The use of welding to permanently join plates is common in industry due to its high efficiency. But welding creates thermal stresses, which can lead to residual stresses and physical distortion. This phenomenon directly influences the buckling stiffness of the welded structure. The welding distortion not only makes difficult the erection of the project, but also influences the final quality and cost of production. In this research, the thermo-elastic-plastic conditions were simulated by a three-dimensional (3D) finite element model (FE). Mechanical and thermal properties of the material were applied to the model, leading to eigenvalue analysis of the thermal and… More >