Mohammed Ayad Alkhafaji¹, Yunus Uzun^2,*

CMES-Computer Modeling in Engineering & Sciences, Vol.136, No.1, pp. 709-732, 2023, DOI:10.32604/cmes.2023.024236

Abstract This paper explains step-by-step modeling and simulation of the full circuits of a battery control system and connected together starting from the AC input source to the battery control and storage system. The three-phase half-controlled rectifier has been designed to control and convert the AC power into DC power. In addition, two types of direct current converters have been used in this paper which are a buck and bidirectional DC/DC converters. These systems adjust the output voltage to be lower or higher than the input voltage. In the buck converters, the main switch operates in conduction or cut-off mode and… More >

J. Aran Glenn^1,*, Srinivasan Alavandar²

Intelligent Automation & Soft Computing, Vol.36, No.2, pp. 1523-1545, 2023, DOI:10.32604/iasc.2023.033545

Abstract Nowadays, researchers are becoming increasingly concerned about developing a highly efficient emission free transportation and energy generation system for addressing the pressing issue of environmental crisis in the form of pollution and climate change. The introduction of Electric Vehicles (EVs) solves the challenge of emission-free transportation while the necessity for decarbonized energy production is fulfilled by the installation and expansion of solar-powered Photovoltaic (PV) systems. Hence, this paper focuses on designing an effective PV based EV charging system that aids in stepping towards the achievement of a pollution free future. For overcoming the inherent intermittency associated with PV, a novel… More >

S. Pandeeswari^1,*, S. Jaganathan²

Computer Systems Science and Engineering, Vol.45, No.3, pp. 2811-2825, 2023, DOI:10.32604/csse.2023.029945

Abstract The Brushless DC Motor drive systems are used widely with renewable energy resources. The power converter controlling technique increases the performance by novel techniques and algorithms. Conventional approaches are mostly focused on buck converter, Fuzzy logic control with various switching activity. In this proposed research work, the QPSO (Quantum Particle Swarm Optimization algorithm) is used on the switching state of converter from the generation unit of solar module. Through the duty cycle pulse from optimization function, the MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) of the Boost converter gets switched when BLDC (Brushless Direct Current Motor) motor drive system requires power. Voltage Source… More >

Oleg P. Dimitriev^*

Journal of Renewable Materials, Vol.11, No.4, pp. 1555-1600, 2023, DOI:10.32604/jrm.2023.024772

Abstract Thermal energy, i.e., the electromagnetic energy in the infrared range that originates from the direct solar radiation, outgoing terrestrial radiation, waste heat from combustion of fuels, heat-emitting electrical devices, decay of radioactive isotopes, organic putrefaction and fermentation, human body heat, and so on, constitutes a huge energy flux circulating on the earth surface. However, most energy converters designed for the conversion of electromagnetic energy into electricity, such as photovoltaic cells, are mainly focused on using a narrow part of the solar energy lying in the visible spectrum, while thermomechanical engines that are fueled by heat in the broad energy range… More > Graphic Abstract

R. Muthamil Arasi^1,*, S. Padma²

Intelligent Automation & Soft Computing, Vol.36, No.1, pp. 997-1012, 2023, DOI:10.32604/iasc.2023.032645

Abstract The developing populace and industrialization power demand prompted the requirement for power generation from elective sources. The desire for this pursuit is solid due to the ever-present common assets of petroleum derivatives and their predominant ecological issues. It is generally acknowledged that sustainable power sources are one of the best answers for the energy emergency. Among these, Photovoltaic (PV) sources have many benefits to bestow a very promising future. If integrated into the existing power distribution infrastructure, the solar source will be more successful, requiring efficient Direct Current (DC)-Alternating Current (AC) conversion. This paper mainly aims to improve controllers’ performance… More >

S. Harika^1,*, R. Seyezhai¹, A. Jawahar²

Intelligent Automation & Soft Computing, Vol.36, No.1, pp. 895-910, 2023, DOI:10.32604/iasc.2023.031829

Abstract The solar powered systems require high step-up converter for efficient energy transfer. For this, quasi-impedance network converter has been introduced. The quasi-impedance network converter (QZNC) is of two types: type-1 and type-2 configuration. Both the type-1 and type-2 QZNC configurations have drooping voltage gain profile due to presence of high switching noise. To overcome this, a new quasi-impedance network converter synchronizing the switching circuit with low frequency noise has been proposed. In this paper, the proposed QZNC configuration utilizes the current controlling diode to prevent the output voltage drop. Thus, the suggested topology provides linear high voltage gain profile, low… More >

N. Hariharan^1,*, Y. Sukhi², N. Kalaiarasi¹

Intelligent Automation & Soft Computing, Vol.36, No.1, pp. 401-414, 2023, DOI:10.32604/iasc.2023.030768

Abstract The voltage fluctuation in electric circuits has been identified as key issue in different electric systems. As the usage of electricity growing in rapid way, there exist higher fluctuations in power flow. To maintain the flow or stability of power in any electric circuit, there are many circuit models are discussed in literature. However, they suffer to maintain the output voltage and not capable of maintaining power stability. To improve the performance in power stabilization, an efficient IC pattern based power factor maximization model (ICPFMM) in this article. The model is focused on improving the power stability with the use… More >

V. V. Nijil^*, P. Selvan

Intelligent Automation & Soft Computing, Vol.36, No.1, pp. 1043-1062, 2023, DOI:10.32604/iasc.2023.028028

Abstract Alternating Current–Direct Current (AC–DC) converters require a high value bulk capacitor or a filter capacitor between the DC–DC conversion stages, which in turn causes many problems in the design of a AC–DC converter. The component package size for this capacitor is large due to its high voltage rating and capacitance value. In addition, the high charging current creates more problems during the product compliance testing phase. The shelf life of these specific high value capacitors is less than that of Multilayer Ceramic Capacitors (MLCC), which limits its use for the highly reliable applications. This paper presents a feasibility study to… More >

R. K. Negesh^1,*, S. Karthikeyan²

Intelligent Automation & Soft Computing, Vol.36, No.1, pp. 1151-1172, 2023, DOI:10.32604/iasc.2023.027764

Abstract In the recent era, the significance of Renewable Energy (RE) sources in the process of power generation has attained considerable attention as it provides multiple beneficial impacts without harming the environment. The Photovoltaic (PV) and Doubly-Fed Induction Generator (DFIG) fed wind turbine are employed as hybrid power sources in this study. The output voltages of these sources are independently controlled by separate controllers in an optimal manner for effectively maximizing the overall performance of the system. The Reboost Luo converter is introduced in this work to maximize the output voltage of PV in an efficient manner whereas the Grey Wolf… More >

P. Jenitha Deepa^*, H. Habeebullah Sait

Intelligent Automation & Soft Computing, Vol.35, No.3, pp. 2703-2715, 2023, DOI:10.32604/iasc.2023.030496

Abstract Single Phase Induction Motor (SPIM) is widely used in industries at starting stage to provide high starting torque. The objective of the work is to develop a drive for Single Phase Induction Motor that does not use a start or run capacitor. In this work, the researchers present the details about Maximum Power Point Tracking using series-compensated Buck Boost Converter, resonant Direct Current (DC) to Alternate Current (AC) inverter and matrix converter-based drive. The proposed method provides a variable starting torque feature that can be adjusted depending upon machine load to ensure Power Quality (PQ). The system uses Series Compensated… More >